☰

Philco Repair Tips




AIWA
BEKO
CCE
CINERAL
DAEWOO
FUNAI
GRADIENTE
GRUNDIG
HITACHI
ITT
JVC
LG
MITSUBISHI
PANASONIC
PHILCO
PHILIPS
PIONEER
RCA
SAMSUNG
SANYO
SHARP
SONY
THOMSON
TOSHIBA
VESTEL


Search: philco
Results: 4811
Make Model Symptom Problem Solution By
PHILCO PCM2044
Vertical closed Ic 601 juci
PHILCO PCR 2049
Turns off by itself after about 10 minutes C 704 (471/2kv) MB ELETRONICA
PHILCO TP-2920
Horizontal closing on the sides (cushion effect) Zd1702 with leak (does not show on multimeter) Replace do diodo zener zd1702 (8v2) andlss
PHILCO TP 1454
Does not turn on, LED blinks R922, cold welding Resolved jcosme
PHILCO TPF 2940
Turns off immediately after turning on. C1701 e c 1703 Replace without measuring. Manoel
PHILCO TP-1454
Turns on standby, but does not turn on DS08 Shorted diode, just replace it This email address is being protected from spambots. You need JavaScript enabled to view it. Marcondes Jaicós-PI Ohm eletronica
PHILCO TP 2052
Blinking led Resolder smd components at the power supply ÁdrianChapadãodoCéu
PHILCO TP1454
No video, screen with colored spots R910 ​​and 912 If your phone is buzzing, replace d909 short marcondes, OHM eletronica Jaicos-PI
PHILCO TP2052N
It doesn't turn on beeping without the +b on the flaybk pin The cause was the shorted capacitor c924, sending the +b to ground. I replaced the capacitor and the power supply armed, I hope this tip helps some friend on the forum. This email address is being protected from spambots. You need JavaScript enabled to view it.
PHILCO PC2043
CPH-5 		Turns off and buzzes R706 e c716 R of 10k replaced and c22n replace both marcondes, OHM eletronica Jaicos-PI
PHILCO PCS2952N
Burned fusil D909 d911 eo c904 And cool file josé da eletronica schayonara em florip
PHILCO PCM1443
TV turning on the power supply and maintaining the 20v power supply Causa dz904 marcondes, OHM eletronica Jaicos-PI
PHILCO TP 2010
TV doesn't turn on, stays on stand by 8n2 capacitor 701 Ohm eletronica
PHILCO TP1452N
? 		Out of tune C208, semi capacitance Troar. This email address is being protected from spambots. You need JavaScript enabled to view it.
PHILCO TP1452N
? 		Out of tune C208 sem capacitance Replace This email address is being protected from spambots. You need JavaScript enabled to view it.
PHILCO TP1452N
? 		Out of tune C 208 without capacitance Replace it. This email address is being protected from spambots. You need JavaScript enabled to view it.
PHILCO TP20V56
55 02 F6949 06 2 		Vertical heating, with some scratches on the bottom of the screen Cold solders, on the IC pins and smd capacitors that belong to the vertical. and at two solder points that go to pin 1 from the vertical to the r612a. I did the general repair and it worked normally again. eletronica melo boa viagem ,ceará
PHILCO TP-2053
Dark image then turns off and standby LED flashes Cold solder on the terminals of the FC806a cable connected to the socket on the kinescope board Resolder the f806a cable that is connected to the kinescope board guaracy borges
PHILCO PCR 2049
Does not turn on, horizontal noise C704 (471/2kv) MB ELETRONICA
PHILCO PCS 2976
Turns on and off with LED flashing until it burns out r917(2k2) Cold welding d908 and d909 Resolder and replace the resistor ÁdrianChapadãodoCéu