Philco Repair Tips

Search: philco
Results: 4775

Make	Model	Symptom	Problem	Solution	By
PHILCO	TP2054 NãO TEM	Stand by and TV doesn't turn on	Power supply of plus b with 10t8 volt and +b 10 volt and - b 10 volt	Replace r 706 of 2k2 which goes to pin 33 of ic 101	luiztvsom
PHILCO	TP2054	Dark screen with only characters, whether on the av or channels	Replace r303=4r7 smd		This email address is being protected from spambots. You need JavaScript enabled to view it.
PHILCO	PCS 2956	Doesn't start	C 921 1k/1kv ceramic capacitor (blue)	After removing the shorted capacitor, the TV turned on and quickly turned off, only when adding another capacitor of the same value did it start working again.	José Gusmão
PHILCO	PCM-1444	Does not turn on or off with the remote control	Q904		Moraes
PHILCO	PT 1554 CP02 RO	TV defect has no image in 15 seconds	TV turns off without showing image just plot	Ci power supply ic 901 tda16846 p d 909 short burn r 910 and 912	Everardes
PHILCO	PCM2051	Sometimes it turns on and doesn't turn on and when it turns on over time it turns off by itself.	C708 ou c709		Sandro T Grachet
PHILCO	TP 2054	Dark screen with sound and menu ok,	Cause diode leakage d 602		ELETRONICA ROBSON(DEBIQUE)
PHILCO	PCS 2956	Vertical closed	Vertical was burned out, I replaced the vertical, it remained closed	R 709 open 1r	negodrama
PHILCO	TP-1452N	Volume increases only in 3 stages	Program memory or press the channel +/- key and plug in for 15 seconds and adjust		ELETRONICA ARNI L. LEAL-SC
PHILCO GRADIENTE	TODOS DE 29'' TODOS COM MICRONAS	Transistor h burns out for no apparent reason	Check, change all filter+b capacitors of driver h	Place bu that supports higher current and higher peak voltage	josé carlos
PHILCO	TP14U56	Normal image then goes dark and tsound is only sound	Diode d 602 altered		This email address is being protected from spambots. You need JavaScript enabled to view it. BRUNONIKACIO@HOTMAIL
PHILCO	PC1444 CPH05	Ugly image (no contrast) no sound.	Tda8361 with internal defect	Replace the tda8361 e5	josé carlos
PHILCO	PC1444 CPH05	Image shaking, synchronization and missing color	Change cap 205. exhausted 2.2mf 50v		josé carlos
PHILCO	TP-2052N	TV asking for password, in my case it asked for password on channel 3.	Reset to memory.	Press the channel + and channel - keys and plug in for 15 seconds.	This email address is being protected from spambots. You need JavaScript enabled to view it. ELETRONICA SÃO FRANCISCO
PHILCO	TP-1454	Doesn't start	D-909 opened d-908 changed		GBS.Eletrônica
PHILCO	TP-1454	Doesn't start	D-909 amended		GBS.Eletrônica
PHILCO	PCM1444	Does not respond to keyboard commands	Cause:r713 (changed or opened)	Replace and resolve	jarbas santos
PHILCO	TP2920	Turns on, no image appears, and then turns off, goes into protection	Check +b 50v from the vertical ci should have around 42v on pin 3 vertical ci, if it is below this ci value defective.		Bruske
PHILCO	PH21B	Turn on the TV perfect image after a few minutes the image starts to lose its brightness due to this defect	In the abl but it is not, defect in the kinescope board transistor bf 423 with emitter collector leak	Replace transistor v 903 bf 423	fernando timbauba PE
PHILCO	PCM2044	It doesn't have 95 volts	C911 220mfx160vols reset		juci