Philco Repair Tips
Search: philco
Results: 4775
Results: 4775
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| PHILCO |
TPF2130
|
It turns on but when the relay goes off a brief image appears with the frame closing horizontally, it goes to stand by with the LED flashing. | C701 (horizontal deflection) auterated | Replace the c701 (8.2 nf/1.6kv) | Ricardo Moreno |
| PHILCO |
PCS 2956N
|
High voltage spikes and turns off | Width defect, replace 8n2 and 4n7 ceramic width capacitors and increase the vertical output transistor decipher (2) | Prado | |
| PHILCO |
PC2956
|
Tsound is no voltage in the secondary of the power supply, it just pulses. | C-921=1k per 1kv of shorted disc, only replace with one of the same value, if not the voltage variation. | It was replaced for one of the same value and it was... ok. | Armando da Eletrônica só Tv. |
| PHILCO |
PCS2952
|
It keeps beeping, beeping and the LED is blinking. | Q 902. | I started it off and it worked. | |
| PHILCO |
TPF 2140
|
It doesn't turn on and it doesn't work on standby. | C 930 with leak in the power supply primary | levilp | |
| PHILCO |
PCM2044
CPH05 |
Vertical fexado. | R.602 | Replace. | |
| PHILCO |
PCS-2956
CP-01-LR01 |
Power supply does not start and chopper driver smokes on pin 7 | C922 short (1.0 nf) I replaced it and the problem was solved. | Note: as the c922 is on the pulse line (130v) the power supply activates and disarms successively. | Tecnogil Eletronica |
| PHILCO |
PT20V56
|
Vertical beam and then switches off | Ceramic capacitor c614 | ELETRONICAAC | |
| PHILCO |
TP20V56
|
Vertical beam and then switches off | Ceramic capacitor c614 | Ac electronics | |
| PHILCO |
PCS2952
|
Dark image with little contrast | C 716 short /r706 open | betoteck | |
| PHILCO |
TPF 2121
|
Morta (nem da stand by) | D908 e c914 | Obs: mude c914 p/ 1000y/35v | VSE Eletrônica(Ádrian) |
| PHILCO |
TP2054
|
Does not turn on, LED is off. | R 911 amended. | Replace. | |
| PHILCO |
PCM2044
|
Lack of sync and drizzle | C205 - agc and c702 sync. I changed the caps. It started working normally again. |
The two electro/capacitors with high esr. | vxm |
| PHILCO |
TP1452N
|
Does not turn on, stays on standby | When the TV is on stand by with the LED on, replace the zd923 4.7 volt diode and the zd922 3.9 volt diode. | Edilson Ribeiro | |
| PHILCO |
TPF 2941
|
Does not turn on or the LED lights up | All voltages are normal, and the TV does not turn on; fed up with stress, I decided to change [x1] that little crystal that is next to every micro, in this case x1 = 20,250, I changed it, I confirmed, it was the one, [if] it happens, sound's the tip | fabinho@3a | |
| PHILCO |
PCR1449
CPH06M |
C912 with leak, change, note tsound is no general voltage in the secondary | ars | ||
| PHILCO |
PCM-2044
|
When the TV was turned on, it worked with a lot of flickering on the screen and it was difficult to maintain the tuning of a channel and when changing channels it got even worse, it shook the whole screen and was like a simonism of vertical and horizontal | The capacitor c710 with cold soldering, I resoldered it and it was file | It is located next to the dryve of the horizontal | |
| TV PHILCO |
TP 29C21
|
TV doesn't work, STD-BY light stays on | Solution replaced the d-916 smd | jaironuness | |
| PHILCO |
PCM 2044
|
When turning on the image comes back to normal after a while the screen becomes clear until the image disappears | Replace ci tda 8361 s7 | ||
| PHILCO |
PCM 2044
|
No image. No sound, no OSD, screen flashing on the power pin, the voltage fluctuates on and off, disconnect pin 35 on the micro controller and the TV stops turning off. So sound the screen is white as if the screen was at maximum but without a delay line | Tube exhausted zerrrrrrrrrrado |