Philco Repair Tips
Search: philco
Results: 4775
Results: 4775
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| PHILCO |
14CT6401
|
Ripples at 110v | Altered waveform | Replace font scrs | paulo artur rio de janeiro |
| PHILCO |
PC 1427 U
|
Whistle when turned on, but inoperative | Power supply did not arm due to deficiency in filter component | Replace cap906,909,and diode905 | paulo artur rio de janeiro |
| PHILCO |
PCM 1448
|
Turning off by itself | Dz 904 short | paulo artur rio de janeiro | |
| PHILCO |
TP 14U56
*** |
No image check if tsound is power on the filament, when the screen increases it turns very faint white check if tsound is 180v in cap.c-713 if ok, note: rgb circuit must have 180v | Replace shock absorber | wagner | |
| PHILCO |
PCM 1443 EMOTION
*** |
Turning off white screen and retraces | R-715 c-719 | R-715 1r,subs 4r7 c-719 10mf x 350v | wagner |
| PHILCO |
TPF2130
|
Does not turn on, without +14v pin 1 ic905 | Solda fria r931 18r 2w | BETO2828 | |
| PHILCO |
PCS 2078
NãO MARCA |
Bu 2508 dx shorts out | C730 5k6 1kv6 changed and change original bu 2508 dx and increase c715 to 7k5*2kv | luiztvsom | |
| TV PHILCO |
PCM 2046
|
Luminance- | Replaced the c716 10 / 250 volts | TV worked normally. | jaironuness |
| PHILCO |
TP-2053
|
TV doesn't work std-by light blinks continuously but dimly | Changed the vertical output tda9309 | jaironuness | |
| PHILCO |
TP-1452N
|
When turning on tsound is no sound after a while the sound starts to come back hoarse. | Change the audio output | ||
| PHILCO |
TP-1452
|
TV with normal power supply, when turned on it generates and cuts in 1 second | Check r713 of 1k8 changed | Daniel | |
| PHILCO |
PC 20R42
|
Interference on the screen without video TV has sound | Replace c301 0.47/35 votes | jaironuess | |
| PHILCO |
PC- 20R42
** |
TV out of horizontal frequency | Or capacitor 303 of 47/35 votes was exhausted | jaironuness | |
| PHILCO |
TPF 2941
|
It has a power supply but no gun | It fell, it was fixed, the trails worked normally; after two days it broke down, it was left alone in the waiting room | carlos branco | |
| PHILCO |
PCM2044
|
When the TV was turned on, the image was shaking, and when the volume was increased, the image was even more shaky. | I checked the power supply and it was normal, but when I removed the capacitor from the power supply input I realized that it had a bad, rotten leg, the 400v/220mf c905 replaced it and went for a hug | ||
| PHILCO |
PCM1443
|
Image blinking as if it were a stand by LED, normal frame, normal voltages, except video voltage; controls inoperative. | R713(100k) open. | Replace r713(100k), device ok. | clayton |
| PHILCO |
TP1454
|
Problem with the colors, it remains without demagnetizing the kinescope. | Check the "epcos" brand component with placement number th 901. this component is connected together with the kinescope coil. | Just replace it with another one and go for the hug!!! | FRANCISCO |
| PHILCO |
TPF-2901
CP01RL01 |
When turned on, it displays a white screen with horizontal retrace lines and seconds later it turns off. | Replacement of the 4r7 r711 that was open. | Marques | |
| PHILCO |
PCS 2700
|
The TV turns off as soon as it was turned on | This TV doesn't oscillate without the fly back and without the deflector so it would be more difficult to discover the defect. | But in this case it was the bad deflector coil that was causing the TV to turn off | heliomar |
| PHILCO |
TPF 2130
CP 03 |
Does not turn on, tsound is no + 14 vdc pin 1 of ic 905 | Change c 918 open | CARLOS ROCHA |