Philco Repair Tips

Search: philco
Results: 4838

Make	Model	Symptom	Problem	Solution	By
PHILCO	PH29M SS	Low power supply around 40v LED goes out but the TV doesn't turn on the power supply stays the same	C851 .1 with leakage is at the base of q808	Replace c 851	Damião
PHILCO	TV PH21MSS	Does not leave st. by.	Memory, but be careful, I had already installed another one that I recorded with files downloaded from the internet and it didn't work, it only worked when luckily another TV like it came on and I copied the files and switched to the one that had the problem.		reinaldo almeida
PHILCO	PH21M SS	When turning it on, the LED flashes, +b changing to 24v	D818 =fr104 shorted	Replace it and run for the hug	hipereletronica service (maraial-PE) Marcelo
PHILCO	PH 21C	Turns on with vertical closed, then turns off	D 810-replace open diode		MARCELO JOSE
PHILCO	TTV PH 21C	TV does not turn on any voltage on the secondary	Zener diode 12v short non-primary d821		Darci Fuhr
PHILCO	PH24A	Does not turn on, power supply stopped	C203 (2n2/ 1kv polyester capacitor) shorted		Aecio Flavio
PHILCO	PCS2956	Risk on the image, better known as the delay line, which is generally seen on the c728 3n3 1600v	C728 3n3 1600v was replaced		gerson tomaz
PHILCO	PH29	Does not turn on low power supply	Zd804 (4v7)		mega center
PHILCO	TPF-2922	Vertical burnt out, the biggest problem to fix, I used a similar part and it never worked.	The resistor that comes from the 50volrs of the flyback is 18r and the ci tda8177f or tda9302h there is no point in putting the tda8177	Put the correct parts and that's it, blz	fabiusmax
PHILCO	PCM-2046	The standby LED doesn't turn on, it's flashing, only the flyback is defective, be careful friend, even with the +b and the bu disconnected, the power supply is low @@@	Flyback		ELETRONICA ARNI/LEOBERTO LEAL-SC
PHILCO	TPF2922	Burnt resistor r709	Value of resistor r709 is 18r 1/2 if you put lower values it will burn type 1r it will catch fire		fabiusmax
PHILCO	PCM-1451	Call whenever you want, it seems like a bad connection	Intermittently turns on and off...	Changing capacitors c 709, c708, changing both without measuring....	Adriano,rio verde,MS
PHILCO	TPF2121	Altered power supply, (+ b quese 170 volts.) triggering protection.	R919 - (120k) fully open.		Carlos Maia
PHILCO	TPF2121C	Vertical closed	Chap. c614 shorted 47nf ceramic	Replace component note: short on the scale x1 this one is actually shorted, hugs	FABIUSMAX
PHILCO	TP20V56	Image disappearing brightness, starting at the top, normal sound.	D 602 as leak		aelson
PHILCO	PT1410	Inoperative, led off.	It was the broken q901=stp9nc70zpf mosfet, ic901=ta1507p, r918=2k2 starting. I changed it and left for the hug.		ELETRÔNICA MELO BOA VIAGEM -CEARA
PHILCO	PCS-2700	(correction) TV without +b on the secondary, with blinking LED	As previously reported, the capacitor (c 720) is not 10uf but 47uf		Ademar / Videira sc
PHILCO	PCS-2700	TV without +b on the secondary, with blinking LED	Change the electrolytic capacitor (c-720) 10uf x 25v located inside the vertical heatsink		Ademar / Videira sc
PHILCO	2956	Turns on, turns off then arming protection	I realized that it didn't have filament protection, then I discovered that it had 180 volt protection, so I turned off the 10k r725, it worked better when reduced, I found the c1703 changed, I changed it and ran to hug it, then I turned it on to the r725 and it was fine
PHILCO	PH21B	Turning off and on	Strw6553 replacement	Strw6553 replacement	fco