Philco Repair Tips
Search: philco
Results: 4775
Results: 4775
Make | Model | Symptom | Problem | Solution | By |
---|---|---|---|---|---|
PHILCO |
PC1444 EMOTION
CPH 05 |
All normal voltages do not work (95v c911- c915 with 15v or normal 5v, no voltage on the collector of q702) | C704 shorted | New tip... | Elias2305 |
PHILCO |
PCM2044-2046
|
Sobbing and doesn't start | Voltage of 20 is 16v, the others are normal, resolder resistor r708, take 2 wires, solder from the collector q702 to the tt702 pin, follow the trail, the same thing on the other pin from t702 to r708 | Place the wires, follow the tracks from the resistor to the t702 pin and from the q702 collector to the t702 pin | toninho da eletronica |
PHILCO |
PCM2046
|
Doesn't start | There is no 160v on pin 3 of the str 50103, this voltage only comes to the t901 pin | Replace t901 or try to restore it | toninho da eletronica |
PHILCO |
PCM2046
|
Blue screen normal characters | L001 close to the 9v regulator that couples the 9v to the varicap, cracked solder. | Resoldag | toninho da eletronica |
PHILCO |
TPF3221
|
No image on the channels, if you twist the pci, it works | Resolder pip ci and surroundings | WARLEY CESAR | |
PHILCO |
PC2035
|
Nor 95 volts | Shorted flyback | Replace | juci |
PHILCO DVD |
PHT660N
|
No sound from audio outputs, normal out line | Pin 9 of the cis sta540a without the 9v standby, unsoldered them and the voltage appeared, solder them one by one to see which one kills the voltage. Once that was done, there was a short circuit, he replaced it and both ciss started working again. | CALIXSERVICE | |
PHILCO |
PCM1444
|
LED blinking non-stop and without horizontal and vertical synchronization | Tda3653b electrolytic capacitor 2.2 mf c408 replace without measuring | Tda3653b e c408 2,2 | macceletronica |
PHILCO |
TPF 2940
BL29 |
Off stand by does not light up or turn on | Check primary power supply | Direct replace r911 -2m2 r 909 -680k and d 915 replaced | luiztvsom |
PHILCO |
PCM 2046
|
Green league takes time to open | C 722 sold out | Replace the c722 470 16v | gesnier bispo |
PHILCO |
PCS2952
|
TV turning on and off with white lines and glare in the center. | R 705 e c 718 | Replace the resistor and capacitor | ELETRÔNICA VINISOM E TV |
PHILCO |
PCS2700
|
Missing preta na canvas | I will go 18 | Replacement | |
PHILCO |
PCS 2700
|
LED blinking weakly and no +b | Capacitor 220y/200v aberto | ÁdrianChapadãodoCéu | |
PHILCO |
PCS2956
|
Excessive width | Wide capacitors check all | A capacitor 8n2 /1600 c 706 com internal flake. | fematch |
PHILCO |
TP-2920
|
Relay knocking when I press the power key | Flyback | Replace it | HIPERELETRONICA SERVICE(MARCELO) |
PHILCO |
PT2054
|
It doesn't turn on, it just stays with a sensor LED | Ic 902 | Replace of the same | ledilson |
PHILCO |
PCM2046
|
White line (scratch) horizontally on the screen almost in the middle | C722 , 470mf/16v | Alextecnico | |
PHILCO |
TP1452N_TP2052N
|
When turning on the TV using the main key, there is a momentary hissing sound in the speaker as if it were off the air and shortly after the stand by LED lights up and the hissing stops, but when turning on the TV using the power key the hissing comes on again until the image appears and then everything is normal. | R411-33k | ||
PHILCO |
PHT550
|
Doesn't start | Still power supply | Replace of cap.120x200 primary power supply, r15 and r52 (2r), r53 and r54 (300k), t1 and t2 (13005), 3a fuse, check d23,d24,d25,d26, 2ax500v. If the power supply makes a faint whistle and the display does not light up, also replace the secondary q2 and q3 (c1815) | joaomvjr |
PHILCO |
DVT-101
|
Turning off when reading the disc | Change optical drive | eletrônica BRITO |