Philco Repair Tips
Search: philco
Results: 4775
Results: 4775
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| PHILCO |
TPF 2940
|
TV with no picture, normal audio | Remove the wire from the screen and turn it on again with the TV on, the image will appear normally | Replace the kinescope socket (tube). | Delima |
| PHILCO |
PT-2052N
|
The TV turns on but the screen is dark, the sound is normal (note: the filament stays on) | Defective picture tube | Tube replacement | Elet.São Jorge |
| PHILCO |
TPF 2130
|
No channel tuning | Electrolytic capacitor 22 micro farads x 50 volts | Is close to the selector, replace without measuring | Adenilson Boscolo |
| PHILCO |
PCS2952
|
Standby blinking showing low power | Replace c946 | luiz | |
| PHILCO |
TPC-2910
|
Does not turn on LED that is off with noise at the power supply | Power supply reset by releasing the flay back all power supplys are normalized good horizontal output on the 180v or 200v capacitor is measured as a short remove the same the short continues defect in the ic tda 6107q video amplifiers | Ic tda 6107q short replaced just joy | ANTONIO DOS SANTOS LIMA |
| PHILCO-ITAUTEC |
PCM 2046
|
Flyback sparking: his number is b 32 3454-001 | Replace the flyback | ||
| PHILCO |
TP2054
|
LED is on, when you activate the power, it blinks | Flyback | Replace the same | Elias2305 |
| PHILCO |
PCS-2978
|
In bright scenes it turns off and the LED flashes | G2 adjustment in the service menu | When accessing the service menu there is blkcurr (g2 -screen adjustment) =0 if you move it replaces the value, never leave it more than (0). | Hipereletronica service (MARCELO) |
| PHILCO |
PCF 2940
|
When turning on the TV, the LED goes out, but it goes to protection and the LED flashes constantly. | One of the causes peak capacitors are 2 of 5k6 x 1600 kv connected to the horiz ioke pin | macedo domingos | |
| PHILCO |
PH21B
|
Turns on and off then, the power supply voltage goes up and then goes down. | Cause: defective photo coupler | klein | |
| PHILCO |
PSC2976
|
Power supply arms and disarms, filament turns on and off. | Capacitors wide =c715 ,c730 semi-short. | gugu eletronica | |
| PHILCO |
TP1454
|
Doesn't start | Starting normally but secondary +b output with only 26v | Replace d912 | LOU |
| PHILCO - PLATINUM |
TPS-2062N
|
Power supply does not release +st-by LED does not light | R-903 470k changed and the +b setting, which had a voltage of 90v, I adjusted it to 100v and the TV started working again, everything was ok. | Wislen Alves | |
| PHILCO |
PH21B
|
LED blinks and turns off | R552 100k changed | DIGITAL TEC | |
| PHILCO |
TP2054
|
Turns on and off then test: turn off the horizontal part of the coil the TV works | Change c715-730 with leakage. | Elias2305 TO. | |
| PHILCO |
PCM-2044-6
CCCCC |
Hiccuping with blinking LED not starting | Does not oscillate | Redo the tracks from t702 to r703 and c709 to t702 with wire okreplace c709 | ANTONIO DOS SANTOS LIMA |
| PHILCO |
PCM 1443 EMOTION
|
TV with no picture, no sound, screen drizzling even with an antenna. | Solution: replace 2k.7 resistor 201, which connects to the tu-oo2 pin a g c . open resistor. | BARRETO CRUZ | |
| PHILCO DVD |
PM190
|
Doesn't start | Diode zenner zd1 5v6 | Replace diodo zenner zd1 5v6 | johnny busnadiego |
| PHILCO |
TP2920
|
LED does not turn on | Change cap. 1000x16v at power supply | Cap. 1000x 16v fonte | ELETRONICA MAURI JUNIOR |
| PHILCO |
TP2054
|
TV starts working + no image appears. waiting about 5 seconds. appears with a smooth screen, with vertical and horizontal lines wanting to close. | Change the cap. 6n8 x 2kv. which has a low value. (5n6 x 2kv) | ROBERTO PINTO |