Philco Repair Tips

Search: philco
Results: 4838

Make	Model	Symptom	Problem	Solution	By
PHILCO	TP1452N_TP2052N	When turning on the TV using the main key, there is a momentary hissing sound in the speaker as if it were off the air and shortly after the stand by LED lights up and the hissing stops, but when turning on the TV using the power key the hissing comes on again until the image appears and then everything is normal.	R411-33k		This email address is being protected from spambots. You need JavaScript enabled to view it.
PHILCO	PHT550	Doesn't start	Still power supply	Replace of cap.120x200 primary power supply, r15 and r52 (2r), r53 and r54 (300k), t1 and t2 (13005), 3a fuse, check d23,d24,d25,d26, 2ax500v. If the power supply makes a faint whistle and the display does not light up, also replace the secondary q2 and q3 (c1815)	joaomvjr
PHILCO	DVT-101	Turning off when reading the disc	Change optical drive		eletrônica BRITO
PHILCO	TPF 2940	TV with no picture, normal audio	Remove the wire from the screen and turn it on again with the TV on, the image will appear normally	Replace the kinescope socket (tube).	Delima
PHILCO	PT-2052N	The TV turns on but the screen is dark, the sound is normal (note: the filament stays on)	Defective picture tube	Tube replacement	Elet.São Jorge
PHILCO	TPF 2130	No channel tuning	Electrolytic capacitor 22 micro farads x 50 volts	Is close to the selector, replace without measuring	Adenilson Boscolo
PHILCO	PCS2952	Standby blinking showing low power	Replace c946		luiz
PHILCO	TPC-2910	Does not turn on LED that is off with noise at the power supply	Power supply reset by releasing the flay back all power supplys are normalized good horizontal output on the 180v or 200v capacitor is measured as a short remove the same the short continues defect in the ic tda 6107q video amplifiers	Ic tda 6107q short replaced just joy	ANTONIO DOS SANTOS LIMA
PHILCO-ITAUTEC	PCM 2046	Flyback sparking: his number is b 32 3454-001	Replace the flyback		This email address is being protected from spambots. You need JavaScript enabled to view it.
PHILCO	TP2054	LED is on, when you activate the power, it blinks	Flyback	Replace the same	Elias2305
PHILCO	PCS-2978	In bright scenes it turns off and the LED flashes	G2 adjustment in the service menu	When accessing the service menu there is blkcurr (g2 -screen adjustment) =0 if you move it replaces the value, never leave it more than (0).	Hipereletronica service (MARCELO)
PHILCO	PCF 2940	When turning on the TV, the LED goes out, but it goes to protection and the LED flashes constantly.	One of the causes peak capacitors are 2 of 5k6 x 1600 kv connected to the horiz ioke pin		macedo domingos
PHILCO	PH21B	Turns on and off then, the power supply voltage goes up and then goes down.	Cause: defective photo coupler		klein
PHILCO	PSC2976	Power supply arms and disarms, filament turns on and off.	Capacitors wide =c715 ,c730 semi-short.		gugu eletronica
PHILCO	TP1454	Doesn't start	Starting normally but secondary +b output with only 26v	Replace d912	LOU
PHILCO - PLATINUM	TPS-2062N	Power supply does not release +st-by LED does not light	R-903 470k changed and the +b setting, which had a voltage of 90v, I adjusted it to 100v and the TV started working again, everything was ok.		Wislen Alves
PHILCO	PH21B	LED blinks and turns off	R552 100k changed		DIGITAL TEC
PHILCO	TP2054	Turns on and off then test: turn off the horizontal part of the coil the TV works	Change c715-730 with leakage.		Elias2305 TO.
PHILCO	PCM-2044-6 CCCCC	Hiccuping with blinking LED not starting	Does not oscillate	Redo the tracks from t702 to r703 and c709 to t702 with wire okreplace c709	ANTONIO DOS SANTOS LIMA
PHILCO	PCM 1443 EMOTION	TV with no picture, no sound, screen drizzling even with an antenna.	Solution: replace 2k.7 resistor 201, which connects to the tu-oo2 pin a g c . open resistor.		BARRETO CRUZ