Philco Repair Tips
Search: philco
Results: 4775
Results: 4775
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| PHILCO |
TPF2922
|
Normal league, with horizontally expanded image | The dz1701 was replaced | ROBERTO PINTO | |
| PHILCO |
TPF2922
|
Sometimes it turns on, sometimes it doesn't. When it turns on, it has a black stripe at the top and bottom, with excess red in the image. | The precision resistor r725 was replaced and an adjustment was made to the flyback screen | ROBERTO PINTO | |
| PHILCO |
PC1443
|
Vibrating t901 (power supply buzzing), not having high voltage. | C921 to power supplys. | C291 de 22n/50v | Ademir tc |
| PHILCO |
PCM2044
|
Doesn't catch any channel | Ceramic capacitor | Ceramic capacitor on pins 42,43 and 44 responsible for inputting vhf,μHf and vl signals | WILLIAN8952 |
| PHILCO HI |
PC1442
|
No sound normal image | C420 shorted | Replace | EletroClaudio Aguas Belas |
| PHILCO |
PH200
|
Inoperative, only blue volume LED on! | Open smd l4 inductor | Replace l4 for another... | pfa |
| PHILCO |
TPF2121F
|
The TV only turns on by pressing the power button on the panel, that is, it does not turn on with the control. | Defective sensor, position ir1101 which is on the plate on the front panel of the TV, sensor rpm-693b. | It was replaced for an identical one and it looks great!... | Armando de Olímpia |
| PHILCO |
TP-2052N
|
Dark screen with no image and with normal sound when the screen increases, a torch appears like an arcuires | Defective vertical output tda8356 | Replace | EletroClaudio Aguas Belas |
| PHILCO |
PCM2044
|
Poor convergence, in the image and characters, and heating up r711 | Oxidized deflector coil | Replace deflector | PALAURO |
| PHILCO |
PT
|
Power supply did not oscillate | Ic do som | Replacement | |
| PHILCO |
PCM-2051
|
Volume increases or decreases every 10 points | Memory defect | Reset the memory: unplugged, press and hold the ch+ and ch- keys on the TV. Turn on the power and wait about 5 seconds until the stand-by LED lights up. release the pressed keys and turn on the TV and reprogram the channels and settings. If the defect returns, replace the memory and perform a reset. | Diego PG-PR |
| PHILCO |
PCS-2976S
|
Resolder tube board 6 wire mesh | Resolder | SEM IMAGEM TELA AZUL COM RETRAÇO | |
| PHILCO |
PCS-2956N
|
Works for a while and turns off | Weapon protection | I removed the resistor r 932 and it worked normally | noel batista |
| PHILCO |
PH200
|
Does not turn on as if the power supply has a problem | Remove the tda7265 sound output, if it turns on, replace it | Replace sound output | Cezar |
| PHILCO |
PCM 2051
|
The TV turns on and off in seconds | R 705 3r3 measuring good to put a jamper | eletronica rodrigo 048 32429465 | |
| PHILCO |
TP2920
|
When it turns on, the LED goes off, the tube blinks a few times and goes off, then the LED keeps blinking | Changing capacitors c1701 and c 1703 6n8x1k6v polyester.......it was zero again!!!! | adilson | |
| PHILCO |
PH14C
|
Dark image | BF 422 and 423 leaking, change all BF's on the TRC board | Continental | |
| PHILCO |
PCM 1444.2044
|
No color. | Swap.c.504. | Resolved | hermildon jose t de sousa |
| PHILCO |
TP14U56
|
When plugged into the socket, the power supply gave a signal that it would work but it didn't, and the LED didn't even light up. and the +b voltage was just 10v and the normal 4.7v voltage | R107 of the LED and e-prom system was open and the sw101 was broken. | I replaced the touch switch on the power sw101 and it turned on but the LED didn't work, I replaced the 100k or107 and the LED came on then it was just a hug. | DIGITEC ELETRONICA (65)9608-4535 |
| PHILCO |
PC-1438
|
Does not turn off via remote control | Q-902 | Replace and test. | ELETRONICA NISSEI SOUND embu-sp |