Philco Repair Tips

Search: philco
Results: 4775

Make	Model	Symptom	Problem	Solution	By
TV PHILCO	PCM 2051	This Philco PCM2051 TV received no image. on the fly back, pin 6 should have 45v and has zero and on pin 5 it should have 180v and has 80v. When he was admitted, the varicap was broken inside (coils). I replaced the varicap and the transistor q201 and c206 to repair the channel programming, which was not working. It turns on normally, gets a blurry image and if you move the screen, there is a recoil.	I managed to resolve the defect. I replaced the fly back due to lack of internal insulation. I also managed to change the varicap at the dealer and resolved the high voltage on pin 7 of the varicap, it was defective.		BF.COLATNO
TV PHILCO	TP1454	This TV turns on normally but with no image or AV, it has 33v on the varicap, I already changed the varicap, memory, as soon as it turns on it starts to produce audio but it disappears.	Cause of this defect was, d602 with escape.		BF.COLATNO
TV PHILCO	29S4F	If I turn off the vertical output of this one, it turns on, if I turn on the output it keeps giving the defect mentioned above, tripping. I already changed the vertical outlet and it didn't help.	The problem was in the deflector socket, I removed it and cleaned it, as it was oxidized, I resoldered it and the problem was resolved.		BF.COLATNO
TV PHILCO	TP 2054	This TV has 3 colored lines at the bottom, what doesn't match is the output on pin 21 of the computer which is at 0.2 v, pin 22 ok is at 0.6 v o + 12 and - 12 v ok.	The c. i. vertical and the voltage at pin 21 of the computer, which was 0.2 v, became 0.5 v, so I just changed the vertical output and the TV returned to normal.		BF.COLATNO
TV PHILCO	TPF 2902	The volume of the TV, it increases every 4	I removed the power cable, simultaneously pressed channel + and - for 20 seconds and it was normal. ,		BF.COLATNO
TV PHILCO	PCM205	This Philco PCM2051 TV received no image. on the fly back, pin 6 should have 45v and has zero and on pin 5 it should have 180v and has 80v. When he was admitted, the varicap was broken inside (coils). I replaced the varicap and the transistor q201 and c206 to repair the channel programming, which was not working. It turns on normally, gets a blurry image and if you move the screen, there is a recoil.	I managed to resolve the defect. I replaced the fly back due to lack of internal insulation. I also managed to change the varicap at the dealer and resolved the high voltage on pin 7 of the varicap, it was defective.		BF.COLATNO
PHILCO	* CPH05	Horizontal bars	C 702 of 1uf with altered ers	By exchanging the capacitor for another of the same value, the defect was remedied.	edrod
PHILCO	TP2920	It turns on then goes into protection, the LED starts flashing.c	C1703 and c1701.		This email address is being protected from spambots. You need JavaScript enabled to view it.
PHILCO	TP1452N	Doesn't start	Defective power supply ci	Tda4605-3 power supply IC replace	johnny busnadiego
TV PHILCO	1454	Then leave and don't care	R910 and r912 open, check diode minus 12 volts was shorted		BF.COLATINO
TV PHILCO	20V56	Drizzle.no channels work	I had 33v and the necessary voltages, but when I checked the date and clock line with the scop (oscilloscope) I saw that there was no clock signal.	R202 100r smd version was open.	BF.COLATINO
TV PHILCO	PC 1446	Works normally but keeps flipping channels	Just wash the processor with theener and the processor is back to normal.		BF.COLATINO
PHILCO	TP2052	+b pressing led off	Capacitor as low capacitance	Replace the 1 μF capacitor c 913 that is in the primary power supply TV ok. good luck	george pontes
PHILCO	PH 21C	Closing vertically at the top and bottom	C401- 882j 100	Barter it	This email address is being protected from spambots. You need JavaScript enabled to view it., jaicós PI
PHILCO	TPF29S4F	TV arrived at the inoperative workshop. I found a diode on the yoke board with a short in position d1701, I replaced it with a new one, the TV started working again, but the screen had stretched corners, I tested the entire yoke board but everything was ok, I went into the service menu and more. it was a defect; Luckily, another TC Philco model TP2920 arrived which had the same chassis, so I ordered the yoke plate and put it in, it was still defective; So, look at the other board, there were two wires coming from the 706 capacitor position going out to the yoke board, so I did it from the other board; negative position of the capacitor n pin 2 of the cm 1307 positive n pin 1, then also change the resistor n position r 1702 to 47k then just joy ;8817	Missing wire that connects the yoke with the position d c 706	Remove capacitor c706 put two wires in its place connect socket cm 1703 which is n yoke + a 47k resistor	marcos melo cascavel ceara
PHILCO	TVPH21SS	Doesn't start, doesn't have +b.	R520 of 120k open at power supply.	It was just a matter of changing it and it was ok.	FRANCISCO - ELETRONICA SÃO FRANCISCO This email address is being protected from spambots. You need JavaScript enabled to view it.
PHILCO	TP2920	Turns on then goes into protection, LED flashes.	Exchange c1701 and c1703
PHILCO	PC2041	Turning off after flyback replacement	Resistor r723 (27k) open abl line		ARAUJO
PHILCO	TP2052	It doesn't turn on, or it oscillates and turns off and the LED keeps flashing	C706 6n8 leaking capacitor	I put another one it worked perfectly	FRANCISCO RS
PHILCO	TP2053N	Blinking LED doesn't turn on	Shorted deflector coil	Replace the coil	francisco rs