Philco Repair Tips

Search: philco
Results: 4838

Make	Model	Symptom	Problem	Solution	By
PHILCO	TP20U56	Without image, with osd and sound	D602	Replace d602 with leak	joaomvjr
PHILCO	PH29C	Blinking LED doesn't work	D 810 fr154		macceletronica
PHILCO	TPW3280	Tries to turn it on, it starts to activate but it doesn't work, the LED keeps flashing	Wide capacitor c708 5n6		macceletronica
PHILCO	PCM 2044	Only in stand by does not oscillate	Closing a short in the collector and emitter of the q 905 oscillates	Changing q904 or even leaving the short may not perform some functions but it works	celito santo angelo
PHILCO	TP2052N	Turning off immediately after turning on	Dz101 3.9v with leak	Replace it	eletrônicatual [nen]
PHILCO	PH 14C	Image erases and switches to one of the colors	Transistor bf 423 rgb output		eletronicaastec
PHILCO	DVD PH155	Doesn't start	Defective photocoupler	Changing the photocoupler	johnny busnadiego
PHILCO	TP-1452N	TV with normal sound / with characters / washed black screen, opens the normal retro screen	Replace flyback		DOIDO DA ANTENA (This email address is being protected from spambots. You need JavaScript enabled to view it.)
PHILCO	PCS-2976	Blurry image.totally out of focus.	Circuito vertical.	Replace.	This email address is being protected from spambots. You need JavaScript enabled to view it.
PHILCO	PVT2010	Does not come out on stand-by	Saida Horizontal / Saida Vertical / Cop. 541	Replace mentioned items	eletronicaapolo
PHILCO	TP2053	TV wasn't turned on, it just kept making noises from the speaker like toooooooooooooo	I checked everything on it and didn't find anything bad.	Then came the surprise: the magnet of the primary power supply transformer was detached, so I glued it back together and it started working again, and the very large transformer that is next to the MOSFET was either loose or detached;	This email address is being protected from spambots. You need JavaScript enabled to view it.
PHILCO	TP1454	It just stays on stand by, +b voltage is around 30 volts and it doesn't work	D-908 shorted killing the 12 volts from the vertical	Replace d-908	samuel leite
PHILCO	PH21MSS	Does not turn on, power supply inoperative	Ic reg de power supply ncp1337p		BRUSKE
PHILCO	PCM 2044	Vertical is from the position	After cold soldering vertically, the image was very open at the bottom and was not in the correct position	Replace c612 10μF x 50v e ajustar no trimpote ok	celito santo angelo RS
PHILCO	TFP2121C	When pressing the "power" key, the standby LED turns off as if the TV were to start normally, but when horizontal it starts to oscillate, the power supply switches off and the STBY LED starts blinking.	C715 (6n8/ 1k6v) with low capacitance, measuring only 4n7		Altevir Lima/ Valparaíso Eletrônica-PA
PHILCO	TVPH14C	Fully blurred screen with three vertical colors	Voltage that polarizes the vertical output (-13v) absent	Re-solder the vd 564 rectifier diode on the power supply transformer	guaracy borges
PHILCO	PCM2046	Does not turn on +b with 30v	Zd904 / r923	Replace mentioned items	eletronicaapolo
PHILCO	PCM-2051	Vertical closed, burning r709 - 1r and d402 - br5404	The tda8356 vertical output ci was replaced and the problem continued. I measured all the capacitors associated with the vertical, I found the c-630 - 47k shorted	C-630 - 47k ceramic short	Osmar Antonio
PHILCO	PCR1449 CPH-06M	Pulsing hard and killing the 180volts.	It was the defective deflector, I replaced it and the TV worked normally.		ELETRÔNICA MELO-BOA VIAGEM-CEARÁ
PHILCO-ITAUTEC	TPF-2121	TV doesn't turn on, and everything stops	Capacitor c 921 1n 1000v em curto	C921 was replaced and everything was ok.	João Carlos