☰

Philco Repair Tips




AIWA
BEKO
CCE
CINERAL
DAEWOO
FUNAI
GRADIENTE
GRUNDIG
HITACHI
ITT
JVC
LG
MITSUBISHI
PANASONIC
PHILCO
PHILIPS
PIONEER
RCA
SAMSUNG
SANYO
SHARP
SONY
THOMSON
TOSHIBA
VESTEL


Search: philco
Results: 4775
Make Model Symptom Problem Solution By
PHILCO PC2013U
CPH02 		Vertical closed Capacitotor c 611 de 100uf/100v rim Also replace c607 at 10μF/63v and c609 at 4.7μF/63v francisco rs
PHILCO PCM2146
Inoperative, stand-by LED flashes and does not turn on Capacitor c905, replace as it is open claudio e reinaldo
PHILCO TP-2054 = TP-2053
It doesn't turn on when the standby LED starts blinking +b at 109v it drops to 15v @@@ Saida vertical tda9309 tv tp-2053 a tv tp-2054 vertical tda9302 a ou h Help yourself, leave your tip ass.arni ELETRONICA ARNI-LEOBERTO LEAL-SC
PHILCO TP-2054 = TP-2053
Does not turn on when turned on, the standby LED flashes D09, R10=47.0, R12=47.0 ELETRONICA ARNI-LEOBERTO LEAL-SC
PHILCO TP-2054
E.a doesn't turn on LED keeps flashing @@@@ D09, R10=47.0, R12=47.0 Help yourself, leave your tip ass.arni ELETRONICA ARNI-LEOBERTO LEAL-SC
PHILCO TP20V56
CP02R0 		Doesn't start D909 in the power supply secondary luiz g.silva
PHILCO TP20V56
CP02R0 		Doesn't start Power supply secondary d900 luiz g.silva
PHILCO PCM2044
Verticalopen only 5cm from the middle upwards C-613 pin 3 of vert output. 2n2 was with 1n6 joaoxx
PHILCO TP-2052N
Does not turn on, LED off, device inoperative without voltage on the power supply secondary. Cold welding at the power supply. Resolder r910, r909, d906 and points on the same power supply line. celinvds
PHILCO TP1410
Standby is on but when I turn it on it starts blinking but doesn't oscillate the TV only has +b 106 volts 15 homs resistor burnt or with raw solder check it position r931 and it feeds the 1000mf x 16 volt capacitor take advantage and change it without testing the c918
PHILCO TFP2902
Horizontal shifted right side Capacitor c732 smd 2n2
PHILCO PCM 2044
05 		Vertical closed dark strip at the bottom Capacitor 1000uf35v no esquema c610 I replaced it, it was a jewel dgspeg
PHILCO PCM2044
05 		Vertical closed dark strip at the bottom Capacitor 1000uf35v I replaced it, it was a jewel dgspeg
PHILCO PCS-2956
CPO1LR01 		TV with no image and no sound; with line of retraces. Irregularities in the ic101 (m37274ma), memory, blocked the system when activating the image adjustment in the menu. After replacing the ic 101 (m37274ma), the device was ok. clayton
TV PHILCO PCM 2044
Blinking led Takes about 20 minutes to work Solution capacitor c722 470μFx25v, replaced and resolved. BF.COLATINO
TV PHILCO 20V56
With drizzle. None of the channels worked, before condemning the seletronic I checked that it had 33v and the appropriate voltages, but when checking the date and clock line I saw that there was no clock signal. Following the seletronic backwards I saw that r202 100r smd version was open. because there was a sign on one side and not on the other. I replaced it and that's it. all channels are working again BF.COLATINO
TV PHILCO PCM-2046
Doesn't start After finding that the c716, r706 were broken and replaced I checked that the flayback was shorted and I replaced the components and everything went back to normal. BF.COLATINO
TV PHILCO 2956 N
Entering protection resolved The problem with the TV was the wide capacitor (c 728-3u3 1k6) Replaced and resolved. BF.COLATINO
PHILCO PCM 2044
Turns on and off without stopping R115 open and c718 shorted. These two components are part of the 180v power supply. BF.COLATINO
PHILCO PCS-2976S
Reduced frame on the sides, stretched vertical, strange characters and could not access service mode. 24c04 smd memory Memory replacement Evandro Bobsin cardoso