Philco Repair Tips

Search: philco
Results: 4775

Make	Model	Symptom	Problem	Solution	By
PHILCO	PCM1443	TV turning on the power supply and maintaining the 20v power supply	Causa dz904		marcondes, OHM eletronica Jaicos-PI
PHILCO	TP 2010	TV doesn't turn on, stays on stand by	8n2 capacitor 701		Ohm eletronica
PHILCO	TP1452N ?	Out of tune	C208, semi capacitance	Troar.	This email address is being protected from spambots. You need JavaScript enabled to view it.
PHILCO	TP1452N ?	Out of tune	C208 sem capacitance	Replace	This email address is being protected from spambots. You need JavaScript enabled to view it.
PHILCO	TP1452N ?	Out of tune	C 208 without capacitance	Replace it.	This email address is being protected from spambots. You need JavaScript enabled to view it.
PHILCO	TP20V56 55 02 F6949 06 2	Vertical heating, with some scratches on the bottom of the screen	Cold solders, on the IC pins and smd capacitors that belong to the vertical. and at two solder points that go to pin 1 from the vertical to the r612a.	I did the general repair and it worked normally again.	eletronica melo boa viagem ,ceará
PHILCO	TP-2053	Dark image then turns off and standby LED flashes	Cold solder on the terminals of the FC806a cable connected to the socket on the kinescope board	Resolder the f806a cable that is connected to the kinescope board	guaracy borges
PHILCO	PCR 2049	Does not turn on, horizontal noise	C704 (471/2kv)		MB ELETRONICA
PHILCO	PCS 2976	Turns on and off with LED flashing until it burns out r917(2k2)	Cold welding d908 and d909	Resolder and replace the resistor	ÁdrianChapadãodoCéu
PHILCO	TPF-2121	Horizontal burnt q701	Replace q701 (bu2506dx) e c715 (6n8/1k6v)		Marcio
PHILCO	PCS 2976	LED blinking very quickly	R917 open	2k2	ÁdrianChapadãodoCéu
PHILCO	PCM 2046	Cesa screen with retrace line	C719 was stuffed	Just replace, send you the tips as well because they help	serginhosond@yahoo
PHILCO	TP2053	Dead power supply	Ic 901 did not oscillate		betoteck
PHILCO	TPF2940	When the TV is turned on after a few minutes, the image darkens at once but the sound continues. Turning it off and turning it on again returns the image normally and after about 10 to 16 minutes it returns with the same defect.	I removed the capacitor c60 9 of 220nf x100v which was measuring about 202nf on the capacimeter. and the c606 of 47nonofaraides x250 vlts apparently good on the capacimeter, but it was bad	I replaced the two c606 and c609 close to the vertical output (note in some cases you have to replace up to the vertical output number; tda 8177f) it remained file	This email address is being protected from spambots. You need JavaScript enabled to view it.
PHILCO	2956N	It went into protection, but when removing the connector from the horizontal deflector it worked normally, (with the horizontal closed of course).	Change wide capacitor (c728;3u3 1k6) there's no point in testing, change it, and run for the hug!!!		abreda
PHILCO	1444	Turns on without characters on the screen, changes micro and nothing, tests resistors and diodes related to the problem and nothing.	Change ci tda-8361	It was just a matter of changing it and it was fine.	Eronaldo(arteron)
PHILCO-HITACHI	PC-20R42 CH04	Dull	Transistor q301 shorted and diode d305 leaking.		pardalzito
PHILCO	PCM2046	Vertical retrace	Elco c610 100 x 25v		johnny busnadiego
PHILCO	PCM2046	Does not turn on and voltages are ok	Elco c915 from the 20v power supply and can also be the d904 and zd904	Capacitor replace c915 1000 x 35v	johnny busnadigo
PHILCO	PT2054	Burning horizontal outlet	C715 6n8/1k6v	Replace the same	Cezarel