Philips Repair Tips
Search: philips
Results: 14206
Results: 14206
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| PHILIPS |
29GX1999/78
GR6LS |
Doesn't start. tube does not load. LED flashes 4 times. sound working normally. | The 138 volt power supply that powers the horizontal was very low. damaged 100uf/200v and 47uf/250v capacitors. | Gilcimar Rocha Pereira | |
| PHILIPS |
14PT3336
|
Turning off in a few seconds | Bc 337 on the line that feeds the varicap 5 volts | In this case, I wouldn't get the channel either | |
| PHILIPS |
29PT5645/78
|
The stand-by does not turn on | D6533 replace works normally again | marcos soares | |
| PHILIPS |
20GL1340
|
Vertical belt doesn't synchronize, it goes really crazy, regular power supply trimpot goes fine and then locks up again | Brown capacitor behind tda 8305, c162 number 223 | Replace the capacitor | celito santo angelo |
| PHILIPS |
40PFL8605D/78
|
Dead | Ray | Replace u101, d301 | felipe |
| PHILIPS |
29PT5642
|
Twisting image after changing the flyback for an mxt or fbt | Image becomes distorted when white parts with high contrast appear | Remove the ferrite from the original flyback and place it in the mxt or fbt | Eletrônica Solar |
| PHILIPS |
21PT8467/78
|
Mute / vertically closed / 5 centimeters at the bottom and top | Eeprom-24c16wp | moreno-pirat. | |
| PHILIPS |
20GL1345
|
TV turns off quickly after turning it on, sometimes it doesn't even turn on | Q7537 (f423) near fly with small leak | zé apolonio | |
| PHILIPS |
21PT9467C
SK4.1L |
3 colored lines appear at the top of the screen | R 358 220Ω/2w | Note that the 21pt9467 scheme is different from the 9767c in the other scheme the position is r304 | JOSÉ GUSMÃO |
| PHILIPS |
32PFL3404
|
Dark image (even more so in the center) | Replacing the power supply board | robson | |
| PHILIPS |
20PT3331/78
|
Turning off. | Solution: adjust fly back screen | BARRETO CRUZ | |
| PHILIPS |
14 PT 3131/78
|
No sound (Audio) | Solution: check ci - an 7523 n and components around it, if ok! d e s a c t i v a r c - 2908 (4.7uf/50v) | BARRETO CRUZ | |
| PHILIPS |
14 PT -3131/78
|
Vertical closed at the top of the screen | Solution: change c - 2444 (470uf/16v) c - 2446 (470uf/16v) c- 2465 (10uf/160v) | BARRETO CRUZ | |
| PHILIPS |
20 PT 3331/78
|
Turning off | Solution: adjust the flyback screen. | ||
| PHILIPS |
14 PT 3131/78
|
No sound (Audio) | Solution: check ci - an 7523 n and components around it, if ok! d e s a c t i v a r c - 2908 (4.7uf/50v) | ||
| PHILIPS |
14PT - 3131/78
|
Vertical closing at the top of the screen | Solution: change c - 2444(470uf/16v) c - 2446(470uf/16v) c- 2465(10uf/160v) | ||
| PHILIPS |
29PT5642
|
TV turns off by itself, sometimes it takes a while to turn off. | Cold solder on the flay-back pin that is connected to ground. | Soldered and ready. | Armando,EletrnicaEvoluSom. |
| PHILIPS |
29PT5645
L0401L |
The power is high but the filament does not turn on, in 5 seconds it turns off | Shorted tube | Replace the tube | cleberlima |
| PHILIPS |
21PT5433/78R
|
Turns on with the image a little blurry and then immediately. | I changed the socket, it improved but the image continued with blurred colors and kept turning off, so I checked that the filament voltage was low, I changed the r3444 and r3443 and it returned to normal. | Replace r3444 and r3443 and check 2444 | dodim |
| PHILIPS |
14PT316A
|
Doesn't start | Change fly back, it turned on but with a hoarse sound, also change potentiometer 3540 adjustment +b leave the adjustment at 95 volts... | pfa |