Philips Repair Tips

Search: philips
Results: 14210

Make	Model	Symptom	Problem	Solution	By
PHILIPS	20PT4331	No sound, increased after a certain time	C 2444 (470 uf) changed	Is close to the fly	cabeção natal
PHILIPS	FW-C380	Crackling sound, as if connecting and disconnecting the speaker (like bad contact) I tested everything that is part of the audio and nothing, I even changed the ci 7501-tda7468, and the 4558 without success	Capacitors c2601, c2602 1nf smds at output 12,17 of the tda 7468 and that's it		az09(elizeu) This email address is being protected from spambots. You need JavaScript enabled to view it.
PHILIPS	DVP3254K	No sound	Ce26 =220/16v with leakage		Bruske
PHILIPS	14PT110B	Image pushed to the left side and without OSD	Tda 8660e from line 5 y	Replace for one of the same good luck	EVALDO GOMES URUÇUI-PI
PHILIPS	14PT110	As soon as it turns on, there is little shine, slightly off focus, very strong color, appearing to be a tube.	Dark screen gradually brightens	The only defect was the tube socket.	This email address is being protected from spambots. You need JavaScript enabled to view it.
PHILIPS	20PT3331/78R	Closing vertical top	C2465(10u/160volt's)		jarbas santos
PHILIPS	21 PT9467	Stop	Resistor 39k aauterated breastplate ci da power supply
PHILIPS	29PT4635 L01.1L AC2K3	Does not turn on, the LED sometimes lights up, the voltage at the base of 7461 and 7463 was 0.11v and at the emitter it was 0.37v, the other voltages were all normal.	Solution: transistor 7406 bu4508dx -> horizontal output *note: the low voltages made me change the transistors 7461, 7463 and the capacitor 2455 but after changing them the voltages remained low, so I concluded that this was due to a short in the secondary of the transformer 5461 this is because of the transistor 7460 -> horizontal output which was burnt and causing a small leak between collector and base and as its base is connected to the secondary of the 5461 this caused a short in it which was reflected in the primary and killed the voltages of 7461 and 7463.		This email address is being protected from spambots. You need JavaScript enabled to view it.
PHILIPS	AZ1134	Cd after a while of use gives an error	6 volt power supply from CD dropping	Replace q3, q7 and q11, place bc337/25 close to the board	ars
PHILIPS	20PT 3331	Black band 05 cm vertically and lines below it doubles the vertical	Replace capacitor 2465 10nf/160v		pedro ironei jr assitel eletronica
PHILIPS	29PT	TV threatening to close the horizontal	Electrolytic capacitor c 2458 2.2mf 100v and replace the wide capacitor		john games
PHILIPS/MAGNAVOX	20MT2136	Does not turn on (electrical discharge)	No power reaches the photocoupler.	Replace ic 7520	Eronaldo
PHILIPS	21PT5433/78R L03.1 L	Does not work (it remains switched off)	Resistor 3445 and 3446 (both 1r) open	Checked the voltage at pin 2 (ic7520) of 13.8v, and main supply of 97v, both ok! then I found that I didn't have the voltages of -12v (diode 6446) and 160v (diode 6447) due to the open resistors.	Anderson Viana - Manaus
DVD PHILIPS	3254K	No audio	Capacitor ce 26 220 x25v	Replaced, it was ok	aliomarp
PHILIPS	14GX1619	Inoperative power supply does not arm	Crimping the horizontal output and with very high tension on the altered fly back pacifier	Replace o fly back	eletroclaudio aguas belas pe
PHILIPS	14GX1619	White screen with colored retrace lines on the front side and no video	Defective vertical outlet	Replace the same	eletroclaudio aguas belas pe
PHILIPS	21PT5435	It has sound, no image and no characters. I measured the screen voltage it was zero. I came to the conclusion that the tube was shorted, I removed the socket and the deflector and tapped around the kinescope tube and the short disappeared. I put the deflector and socket in place. the screen tension arrived and the image appeared normally.	Kinescope with shorted grids, consuming screen voltage.		VALDO RECIFE
PHILIPS	20PT4331/78R	Turns off on tuned channels, in AV it works normally	R3449 open	Replace of the same	paulo
PHILIPS	20PT3331 L0	Customer said that he had gotten water through the antenna; well the power supply was a little low, I cleaned it in the photo attached to the power supply, it started to turn on but it turned off in 3 seconds then it was really bad, the defect was just the scrin joint and it was very low and it turned off then It just increased, it was ok 88178817 francisco mutirao	Increase the scrin potentiometer as much as possible, everything is ok, good luck	Let's help everyone because it's great when you find a tip from a friend who gives a big hug to professional friends	marcos melo cascavel ceara
PHILIPS	20GX 1659	Disarming	After checking everything - stand bi power supply I noticed that when it was turned off the vertical stretched, I replaced it but the defect continued	Solution I replaced the two electrolytic caps, it worked great - no more disarming hug	jose santos vicente