Search: philips
Results: 14209
Make Model Symptom Problem Solution By
PHILIPS GR2.4
Supply is hickupping. Replace lot l5545 cml op503.
PHILIPS GR2.4
Spare part information Spare part information from qg04 onwards the following l.o.t are used: 25" and 28" black line s sets use l.o.t 4822 140 10501 25" and 28" black matrix sets use l.o.t 4822 140 10503 21" sets with 90 degree picture tube use l.o.t. 4822 140 10499 for
PHILIPS GR2.4
Sound mute depending on video-contents of the picture Solder a 12 volt zenerdiode (4822 130 81288) with cathode to the positive side of (+) of c2246. solder the anode of this zenerdiode to earth. solder a 150Ω (4822 116 52211) resistor to the cathode of the zenerdiode. solder the other side of this resist
PHILIPS GR2.4
Set totally inoperative, mainfuse f1600 (2.5at) blown. Replace t7625 (but12af) and d6602-6605 (short circuit). replace ic7614 cnr50 9407.
PHILIPS GR2.4
Set totally inoperative Check c2549 470nf/400v (4822 121 42074).
PHILIPS GR2.4
Set inoperative; squeaking tone from backside tv. lot defective. Replace lot (pos 5545) and line transistor t7545. check r3570.
PHILIPS GR2.4
Set inoperative. supply in overload protection. Replace lot l5545 because of shortcircuit 4822 140 10499 for 21" 90 degrees 4822 140 10501 for 25"/28"
PHILIPS GR2.4
Red picture with fly-back lines after ticking on the neck of crt Picture tube (a51eal65x00) defective.
PHILIPS GR2.4
Radio interference audible in center and rear loudspeakers Add 10 nf capacitor(4822 121 41857) between the following points: point 2/3 of ic7270 and solder the other connection of the capacitor to the track coming from point 5 of connector s84. all these items are located on the dolby interface module.(see servic
PHILIPS GR2.4
Pll-circuit if-eco version has problems with some antenna signals Pll circuit if-eco module modified. c2004=220 nf (4822 122 32927) r3002=470Ω (4822 051 20471) c2007=removed.
PHILIPS GR2.4
Only st.by led on. no start up voltage on sync. ic Check up ic7708 (pin17 low).
PHILIPS GR2.4
Noise in left loudspeaker at low volume Delete on the if-module the following items: 2235, 3211 and 7201. connect the + of c2216 to jumper 9201 (on the if-module). inverse the loudspeaker connection. remarks : this solution does not work on sets with a subwoofer.
PHILIPS GR2.4
No txt on a non-interlaced picture. Replace software g24wecor1.2 by gr24wecor2.2 see service information gr2.x (94.04)
PHILIPS GR2.4
No raster - eht & sound present A1 volts low - check for line collapse with lights off - dry joints scan coils
PHILIPS GR2.4
No picture, no sound; osd ok; volume not adjustable Check and replace if necessary item d6563; byd74c; 4822 130 80915 and item f1559; fuse 1a 65v; 4822 252 51173
PHILIPS GR2.4
No pic after loptx replacement - ht voltage rises and falls C2549 leaky, fuse ref 1534 feed from e-w cct (does not look like a fuse)
PHILIPS GR2.4
No led on, sops transistor is not switching. Start-up c2620 68nf defective (5322 121 42465).
PHILIPS GR2.4
No e/w correction. Check transistor t7530 e/w circuit (5322 130 60159)
PHILIPS GR2.4
No contrast or red in txt Ic7309 pin 2 volts low (2v) . c2358 22n leaky
PHILIPS GR2.4
Motorboating sound in st.by. supply: "on"=143.6v, "st.by"=78v Replace ic7240 (tda1521; 4822 209 73853)