Philips Repair Tips

Search: philips
Results: 14210

Make	Model	Symptom	Problem
PHILIPS	FL2.16	Correction to service information fl 95.01	Correction to service information fl 95.01 ------------------------------------------ correction in the overview of 100hz and proscan boxen. the replacement for service code 4822 212 30534 must be 4822 212 31231 the replacement for service code 4822 21
PHILIPS	FL2.16	Correction to service information fl 95.01	Correction to service information fl 95.01 ------------------------------------------ correction in the overview of 100hz and proscan boxen. the replacement for service code 4822 212 30534 must be 4822 212 31231 the replacement for service code 4822 21
PHILIPS	FL2.16	Correction to product survey 1996-4	Correction to product survey 1996-4 (4822 727 21505) ---------------------------------------------------- on page pcs 41989 is mentioned at: fl1.10 ag11 and higher: control panel 4822 212 31708 fl1.17 ag20 : control panel 4822 212 31708 fl
PHILIPS	FL2.16	Correction to product survey 1993-4	Correction to product survey 1993-4 ----------------------------------- due to the introduction of new software (v67) an extra option bit in option code 4 has to be set. for the following sets 32 has to be added to option code 4: 25pt910a/01/19 25pt912a/0
PHILIPS	FL2.16	Correction	Correction ---------- all diagrams/partslists of the lfr box show on position 7244 an integrated circuit with typenumber n74f74d. however on this position an ic with typenumber n74f125d is used. the codenumber for the correct n74f125d is: 5322 209 61857
PHILIPS	FL2.16	Colours not ok. no r-y on test picture.	No r-y on pin 1 tda4650. c2385 (10nf; 4822 122 32442) is leaking.
PHILIPS	FL2.16	Coloured spot on screen during switch-off	Replace r3037 by 1k3 (4822 051 10132). remarks : introduced in production from week 9334 onwards.
PHILIPS	FL2.16	Colored picture or picture is green/red, fly-back lines	Check zenerdiode 6450 on pin 19-ic7430 on the lsp. new diode must be philips (telefunken does not work), 4822 130 81512
PHILIPS	FL2.16	Bux85f in mikrosops defective	Change the value of c2260 to 4n7f, replace 7270 with transistor bd825 (4822 130 41746).
PHILIPS	FL2.16	Both languages can be heard by dual nicam signals	For fl1-ptv change the software into v89; 4822 900 10732 for all other fl sets change the software into v88; 4822 900 10723 remarks :introduced in production from week 9614 onwards.
PHILIPS	FL2.16	Blue picture, menu and txt are ok.	Check ic7207 (sda9205-2) lfr box (4822 209 31056).
PHILIPS	FL2.16	Blank picture. osd not synchronised and too large, no txt.	Check/replace memory ic 7900 (st24c08cb1; 4822 209 32283).
PHILIPS	FL2.16	Bad synchronisation.	Bad line sync. pulses at c2219 on power supply selection. replace c2219 (220nf; 4822 122 32927)
PHILIPS	FL2.16	Bad picture. picture scrolls. no rc reaction.	+5v was 4,1v instead of 5,1v. replace ic7551 (lm358n; 4822 209 70672)
PHILIPS	FL2.16	Bad pict. no menu. dark bars over pict. red pict. in dig.scan mode.	+5v was 4,3v instead of 5,1v. ic7551 (lm358n 4822 209 70672) defective. ic7209 (saa7158 4822 209 31059) bendic defective.
PHILIPS	FL2.16	Bad geometrie on top and bottom of the picture.	Change the north/south correction panel into 3104 317 72810 (4822 212 31004). the north/south correction panel has been changed. for service the correct one will be delivered.
PHILIPS	FL2.16	Bad focus or focus varies in a new set or after crt replacement	Possible solution: short circuit the focus and the g2 pins of the picture tube with the aquadag coating. switch the set on for approximately 5 seconds. after this return the set to its original condition. check if the focus adjusted normally. if not repla
PHILIPS	FL2.16	Antenna input: no sound. external input: sound o.k.	Check whether crystal 1602 (stereo decoder) 10mhz oscillates. if not replace x1602 (4822 242 80276).
PHILIPS	FL2.16	After a while raster various. (shaky)	Check c2410/2411 (150nf; 4822 121 41854) in raster oscillator.
PHILIPS	FL2.16	After 10 minutes picture becomes red from right side	C2395 on the lsp poorly soldered.