Philips Repair Tips
Search: philips
Results: 14210
Results: 14210
Make | Model | Symptom | Problem | Solution | By |
---|---|---|---|---|---|
PHILIPS |
FL2.16
|
Protection activated due to no +5v from lot. | Check ic7551, lm 358n (4822 209 71825). if ic7551 has to be replaced, it is recommended: 1) for production code ag00-09 add diode bzx79-c18 (4822 130 31024) between 9240 and pin 8 of position 7551, with cathode to pin 8 of ic7551. 2) for production | ||
PHILIPS |
FL2.16
|
Poor colors, no light in picture | Check ic7207 (sda9205; 4822 209 31056). | ||
PHILIPS |
FL2.16
|
Pip picture not in order. | Check r3345 (4822 111 41424) in pip unit, check ic7755 (4822 209 63423). | ||
PHILIPS |
FL2.16
|
Picture very noisy. | Check tuner fq 916 me/bl. | ||
PHILIPS |
FL2.16
|
Picture twists from top | Voltage of pin 8-ic7450 (tda3654q) on the lsp has raised to ca. 20 v. check diode 6451 (bzx79/c5v6; 4822 130 80954). | ||
PHILIPS |
FL2.16
|
Picture twists from top | Voltage of pin 8-ic7450 (tda3654q) on the lsp has raised to ca. 20 v. check diode 6451 (bzx79/c3v6; 5322 130 34834 or bzx79/c10; 4822 130 61219) | ||
PHILIPS |
FL2.16
|
Picture ok after some time | Ic7207 (sda9205-2; 4822 209 31056) defective when set is cold. | ||
PHILIPS |
FL2.16
|
Picture often dark | Check ic7201 in high end-box (saa9042p/a; 4822 209 31851) | ||
PHILIPS |
FL2.16
|
Picture gives black horizontal stripes, also on rgb | Ic72027 sda9205-2 lfr box defective (4822 209 31056). | ||
PHILIPS |
FL2.16
|
Picture disappears shortly after 30" or control does not function. | When hot, 13,5 mhz clock stops working; change the value of r3123 to 1k2. | ||
PHILIPS |
FL2.16
|
Picture disappears for 10-15 minutes and comes back again | Check transistor t7704 (bc856b) (4822 130 60373) on crt panel | ||
PHILIPS |
FL2.16
|
Picture disappears (fly back lines), on stereo and dual leds blink | Check ic7430 (tda4680). when tda4680 is too hot there is no picture (4822 209 31592). | ||
PHILIPS |
FL2.16
|
Overview of sops repair kits | Overview of sops repair kits ---------------------------- fl1.0 ag00 upto ag03 4822 310 20492 fl1.0 ag04 and higher 4822 310 31921 fl1.1 25" and 28" 4822 310 31919 fl1.1 33" 4822 310 31932 fl1.2 4822 310 31932 fl1.6 | ||
PHILIPS |
FL2.16
|
Only red led is on. hardware protection. | Check e/w protection t7540, t7541 (bc547c; 5322 130 42755) and t7542 (bc857c; 5322 130 42756). | ||
PHILIPS |
FL2.16
|
Only green led is on. | +5v and +13v supply a little low (+4,4v and 11,2v) check ic7551 (4822 209 70672) and/or d6551 (4822 130 80954). | ||
PHILIPS |
FL2.16
|
Noise on high volume | Perform the following modifications on the ssp: add on position 3618 4,7nf (4822 122 31784) add on position 3619 jumper (4822 051 10008) connected in series from 2604/4610 to earth. change position 4610 into 1kΩ (4822 051 10102) | ||
PHILIPS |
FL2.16
|
Noise in sound. (also without antenna signal). | Check ic7680 (tda8425v7; 4822 209 63734). | ||
PHILIPS |
FL2.16
|
No tuning when set is cold. | All supply voltages ok? check tuner: fq916me/if; 4822 210 10548 fq916mf/lif; 4822 210 10558 fq944/lif; 4822 210 10556 fq916dme/b; 482 | ||
PHILIPS |
FL2.16
|
No sound, "on, standby, i" leds blinking | 10mhz crystal 1602 on the ssp defective, 4822 242 80276 | ||
PHILIPS |
FL2.16
|
No pip only pip-osd. | No output from sync ic7410 (sda9086-5) on pip panel? replace ic7410; 4822 209 63644 |