Philips Repair Tips
Search: philips
Results: 14210
Results: 14210
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| PHILIPS |
FL2.16
|
Fuzzy white picture. menu and txt o.k. | Check ic7207 (sda9205-2; 4822 209 31056) bendic ic high-end box. | ||
| PHILIPS |
FL2.16
|
Four dark bars over the picture. | The +5 volt was 5.6 volt instead of 5.1 volt. check/replace ic7551 (4822 209 70672). | ||
| PHILIPS |
FL2.16
|
Flyback lines in upperside of the picture. | Check ic7450 (tda3654q; 4822 209 73308). | ||
| PHILIPS |
FL2.16
|
Faulty horizontal sync. (intermittent and temperature-sensitive) | Capacitor 2117 10nf on lfr box mechanically damaged. (4822 122 32422) | ||
| PHILIPS |
FL2.16
|
Faulty horizontal sync. (intermittent and temperature-sensitive) | Capacitor 2117 10nf on lfr box mechanically damaged. (4822 122 32422) | ||
| PHILIPS |
FL2.16
|
Error code (99) after 10 sec. | Ic7551 +5/+13v supply defective. (lm358; 4822 209 70672). | ||
| PHILIPS |
FL2.16
|
Error 13 in memory. | Replace ic7120 on the digital scan box by new software version p83c652 ffp/050; 4822 209 33289). | ||
| PHILIPS |
FL2.16
|
East/west failure in cold condition. | Replace c2611 by 1uf (4822 121 51319) on lsp. remarks : introduced in production in week 9332. | ||
| PHILIPS |
FL2.16
|
Distortion in vertical lines. | Rimple on micro sops? check elco c2261 (100uf/50v; 4822 124 40255). | ||
| PHILIPS |
FL2.16
|
Distorted east-west & jitter on vertical side lines at switch-on. | In the fl1.16 and fl2.16: replace position t7610 on the lsp by bd536fi (4822 130 63508). delete position 2615. replace position 2611 on the lsp by 2,2 uf (4822 124 41576). replace position 3608 on the lsp by 1k (4822 051 10102). in the fl2.24: replace po | ||
| PHILIPS |
FL2.16
|
Distorted east-west & jitter on vertical side lines at switch-on. | Replace position c2611 on the large signal panel by a 1 uf capacitor: 4822 121 51319. remarks : the east-west distortion shows a barrel-shape. the jittering only occurs at the centre of vertical lines at the left- and right-hand side. after warm | ||
| PHILIPS |
FL2.16
|
Dark picture, only green led, no menu or osd. | +5v supply was 4,1v. voltage d6551 was 4,3v instead of 5,6v. check/replace d6551 (4822 130 80954). | ||
| PHILIPS |
FL2.16
|
Dark fuzzy picture. osd and menu not in focus. | +5v was 7.8v and +13v was 15.5v ic7551 (lm358n; 4822 209 70672) defective. | ||
| PHILIPS |
FL2.16
|
Dark and bad synchronised picture, no colour. | Check power supply voltages to lfr box (+13; +5). if too high or too low check ic7551 on lsp (lm358n; 4822 209 70672). | ||
| PHILIPS |
FL2.16
|
Dark and bad synchronised picture, no colour. | Check power supply voltages to lfr box (+13; +5). if too high or too low check ic7551 on lsp (lm358n; 4822 209 70672). | ||
| PHILIPS |
FL2.16
|
Crazy behaviour: no response from rc or controls. | Other phenomenas: volume up/down, spontanuous service mode etc. etc. in areas with top-teletext. replace control software by replacing eprom ic7002 to version v83 (4822 900 10506). for easy mounting also the controlboard 7115 (on ssp) can be replaced by | ||
| PHILIPS |
FL2.16
|
Crazy behaviour: no response from rc or controls. | Other phenomenas: volume up/down, spontanuous service mode etc. etc. in areas with top-teletext. replace control software by replacing eprom ic7002 to version v82 (4822 900 10423). for easy mounting also the controlboard 7115 (on ssp) can be replaced by | ||
| PHILIPS |
FL2.16
|
Correction to the service manual | Correction to the service manual -------------------------------- in circuit diagram b on page 7 of the service manual fl1.14/fl2.14/fl1.16/fl2.16 and fl 1.17 the resistors 3624 and 3625 are not drawn. these resistors should be drawn on the position of 96 | ||
| PHILIPS |
FL2.16
|
Correction to service manual flx.14/16/17 | Correction to service manual flx.14/16/17 and flx.24/26/27. ----------------------------------------------------------- the code number of position 1200 (fuse 3,15 a) is wrong. the correct code number is 4822 070 33152. this fuse is situated on the lsp i | ||
| PHILIPS |
FL2.16
|
Correction to service manual | Correction to service manual ---------------------------- in service manual fl1/2.14, fl1/2.16, fl1.17 aa the code number of the scavem amplifier panel is wrong. the correct code number for this panel is 4822 212 31469. remarks : the code number |