Philips Repair Tips

Search: philips
Results: 14231

Make	Model	Symptom	Problem	Solution	By
PHILIPS	21 PT8467/78	Vertical, closing 2 to 3 centimeters at the top of the tube	Capacitor-2465 of 10x160v, if it persists, trace the capacitor-2460 of 82nkx250		ELETRONICA CAVALCANTE MARTINOPOLE-CE
PHILIPS	25GX1888 VA A	Does not oscillate	Open horizontal driver	Replace driver horizontal	luciano
PHILIPS	21PT9467	When turned on, it shines and closes, when it firms up it leaves a wide, very luminous band at the top	Diode 304 r310 which supplies the vertical with negative voltage and diode 305 and r318 supply voltage 180v.	Went to replace it worked.	genivaldo itumbiara GO
PHILIPS	14PT112A L7L	The device works intermittently (sometimes it turns off by itself)	Cold solder on the ic pins - mc44603a (7520 - power supply oscillator)	Resolder all pins	adhemar caetano da silva (tecmil eletronica)
PHILIPS	20PT122A/78R LZ	TV on standby, when it turns on the LED blinks about 5 times and turns off	Welded chopper pin that goes to ground with cold solder on the secondary		Paim
TV PHILIPS	21PT9467C/78 SK 4.1L	I caught this TV turning on normally, but tsound was no image, only sound, it didn't light up the filament or generate high voltage. After almost setting it on fire. Analyzing the scheme I saw that tsound was d104 which on pin 34 of the ci when measuring I found that it was shorted.	D104 shorted		chinês eletônica solânea-PB
PHILIPS	PT112A	Vertical closed	R3400 (4k7) aberto		eletronica bianca ipira-ba
PHILIPS	29PT4631	It turned on and after a few minutes it turned off; Sometimes it would call with a few lines and hang up.	Era c2455 de 47/25 q7461 bc33725 e q 7463 bc32725.	And just replace these components and run to another TV.	DIEGO LIMA; NOVA TIMBOTEUA PA
PHILIPS	29PT4631/78R	Does not connect to 150v voltage from the normal primary power supply	L5561 27n open and c2561 100mf/160v with leakage	After replacement, it worked normally again	arnaldo j m p
PHILIPS	37PFL5603D/10 Q522. 2ELA	Image with too much brightness, you could see the images, but it looks more like a film negative	T-com board	To replace	luisrufo
PHILIPS	20GL1310	I closed the image and opened it, then, and when I had an image, the image distorted as if it were an AGC defect.	The bad contact that closed and opened the image was on the vertical top and the image distortion was the tda 8305 plus the capacitors, c162=22n, c182=22n disk and c130=6.8uf for 16v, with low capacity.	The vertical CI was resoldered, the three capacitors and the CI TDA8305 were replaced, it was tough but it was resolved...phew!	Armando de Olimpia Eletronica EvoluSom
PHILIPS	21PT5433/78R L03	One more tip for you guys, this TV would turn on normally, after a few minutes it would turn off and it would have a cushion effect and in AV it would turn off immediately	The cause was the open d6445 smd diode connected to the filament line.	Replace d 6445 smd.	This email address is being protected from spambots. You need JavaScript enabled to view it.
PHILIPS	29PT5642 L04	Vertical closes at the bottom and then turns off.	Check voltage on t7605, 5v collector.	Replace of r 3606 56k replaced for more	joaomvjr
PHILIPS	20PT528A	Turns on and has video and audio and turns off	Fb tweak		eletronica bianca ipira-ba
PHILIPS	21PT424A-524A-324A L9-SS	No secondary power supplys - smelled burning	1k c2550 with leak or toast	Replace, use a 2kv one	jasvan souza
PHILIPS	14PT414A/78	Doesn't start. inoperative.	Primary power supply ok. The defect was the open resistor (r3525) of 33Ω at the gate of the switching transistor.		Gilcimar Rocha Pereira
PHILIPS	FWM 143	Inoperative, does not turn on or display.	X301	Replace x301 32,768 mainboard tubular	joaomvjr
PHILIPS	29PT458A/78	When turned on, normal image and sound comes on and then turns off	After having done everything and not solving the problem I found the cause of the defect, an open 10k resistor in position 3204 connected to the RGB connector that comes from the main board to the tube board	Replace the 10k resistor in position 3204 and good luck	PATRICK
PHILIPS	FW-C505	Burned out sound outputs (an 7591)	As it is missing on the market, it can be replaced by the an 17850, just one modification, connect a 2k2 resistor between pin 1 and 2 of the ci.		pardalzito
PHILIPS/MAGNAVOX	14MT2131/78	Dark screen with no sound but with characters	Faulty memory	Replace a eepron 24c16wp	samuel leite