Philips Repair Tips
Search: philips
Results: 14231
Results: 14231
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| PHILIPS |
28PW6532/78R
|
When you turn it on, it turns off and on, off and on... | Bcs 337 and 327 replaced by bd139 and 136 | manin | |
| PHILIPS |
20GX1656
|
Image with small waves, almost serrated | Ver c 2531 | Master eletrônica | |
| PHILIPS |
29PT4635
|
Doesn't start | D-6467 / d-6464 (smd aberto) | Replace with 1n4148 | |
| PHILIPS |
20PT3336/76
|
Dark screen with characters; and normal sound | 100k open resistor r3442 | DIEGO LIMA NOVA TIMBOTEUA PA | |
| PHILIPS |
20PT3331/78
CH |
Turns on with three colored lines and a closed image at the top of the screen and turns off. | I replaced the c2460 and adjusted the screen, the TV started working normally again. | Marcelo Sperb | |
| PHILIPS |
29SX8879
|
Completely stopped | R 3136 =820k open | ramiresrc | |
| PHILIPS |
29PT6566/78
SL04L11 |
Normal image, sound hissing on all channels, I didn't hear any voice, if I increase the volume, the hiss only increases. | Enter service mode and change audio qss from on to off | hndrsn | |
| PHILIPS |
29PT 552A
|
If no power supply, or just the LED blinks | Can be c2463 220/2kv or c2550 with small leak | Remove, for testing, if it works, replace. | jasvan souza |
| PHILIPS |
29PT552A
|
Measure, if bad, replace | C2551 and c2450 with good appearance but exhausted (47/160v both) | Measure, if bad, replace | jasvan souza |
| PHILIPS |
29PT552A
|
Measure, if bad, replace | C2551 and c2450 with good appearance but exhausted (47/160v both) | Measure, if bad, replace | jasvan souza |
| PHILIPS |
40PFL6605
|
Does not turn on, nor does the stand by LED light up | D911/d907 diodes (sb260), as I couldn't find these diodes I put the sb560, it worked perfectly. | These diodes are on the secondary of the power supply | Mauriílio |
| PHILIPS |
20PT 326A/78R
|
Ñ league. | Capacitor 2409(47uf/160v) e capacitor 2551(47uf/160v) | Replace them. | BARRETO CRUZ |
| PHILIPS |
37PFL5332
|
Turns on the image appears for 15 seconds and turns off | U-202 change without measuring | VIDEOTRON | |
| PHILIPS |
20PT324A
L9.2 |
Very weak channel reception | Filter 1003 (m1967m) | joaomvjr | |
| PHILIPS |
21PT9467C
SK-1LCA |
Turns on with image and no sound, doesn't turn on, locks keyboard, turns on only with drizzle or white screen. | Zd604 | saffier | |
| PHILIPS |
29PT5645
|
No image | Shorted picture tube | Replace tube | ELETRONICA MAURI JUNIOR |
| PHILIPS |
20PFL5122
|
Tsound is no image, the lamps do not light up | A faulty light bulb triggers the protection and no one lights up | You need to replace it with a good bulb to avoid triggering the protection, just leave it off | eletronicaaeb |
| PHILIPS |
20GX1669
|
Does not turn on LED blinks 2 times | Ci vertical | Tda8351 | ELETRONICA MAURI JUNIOR |
| PHILIPS |
21PT1663
L7.2E |
Doesn't start. LED blinks weakly and without voltage at the power supply output | C2550 | Substituir c2550 | jose almeida tavares |
| PHILIPS |
25PT5321/11
GR2.4 |
When turned on, the image appears for 1 or 2 seconds, then the screen is dark with return lines and a light line at the top. If you change the screen a little, the video tends to appear very dark. | One of the kinescope's cathodes is nearly short-circuited. in my case it was blue (I tested the cathodes with a rejuvenator). | Use a kinescope rejuvenator to eliminate possible short circuits in the cathodes. | AleVict |