Philips Repair Tips
Search: philips
Results: 14231
Results: 14231
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| PHILIPS |
21PT9467S
|
Vertical folding top with 3 colored lines | R304 de 220r/or | Replace mentioned item | eletronicaapolo |
| PHILIPS |
29PT4641
|
Contrast does not work | 3451 open resistor | pardalzito | |
| PHILIPS |
40PFL3805D/78
|
TV doesn't turn on | D-210 d-510 q-501 r-517 u-501 f-101 | Replace them all | EDILSON AZEVEDO |
| PHILIPS |
21PT5456
|
Turns on with normal image. then turns off. | Change c 2444 of 470 x 16v in the filament line | edimilson de osasco | |
| PHILIPS |
14PT316A
L9.2A |
Turning off in 5 seconds if you hold the channel button + TV it stays on if you release it it turns off | Transistor 7620 bc547 button side channel | Replace | BETO2828 |
| PHILIPS |
29PT9467
|
Suffered an electrical discharge | Replace r-3532 ,ic 7531tea1620 | WARLEY CESAR | |
| PHILIPS |
21GX1666
|
Image all jagged and shaking | Replacement of 47uf 160v c2448,c2447 capacitors | julio.sertemaq | |
| PHILIPS |
HPS- 2185
|
Doesn't turn on anything, totally inoperative. | The stand bay LED does not light up and the secondary transformer has very low voltage | Swap c808. | lou |
| PHILIPS |
29PT4631
L01.1LAC 2K3 |
Does not tune uhf | This defect is caused by the eprom, just adjust it! | Enter service mode, in the option menu, if op 1 is set to 0, replace it to 128, exit service mode and tune again. | |
| PHILIPS |
29 PT
L03. IL |
Without video with lines, but with characters | R 3442 open on fback pin 10 | Tonin Coxim MS | |
| PHILIPS |
14GL1014
|
Black screen no image no drizzle | C2410 no pé do vertical 100uf 25v | Replacelo | antonio nobrega(patos pb) |
| PHILIPS |
FWM416
|
I'm sound | Amplifier on level under pin 13 of the stk433-870 | Replace q721/716 2n5551=mpsa42 e q722 bc556 | VITALTEC |
| PHILIPS |
16GL1333
|
Low 5 v supply, screen with retraces, no image and sound | Ceramic cap 2953 short | pardalzito | |
| PHILIPS |
20PT424
|
The LED keeps shaking and horizontally | Adjust +b in power supply | Agnaldo | |
| PHILIPS |
21PT9467
|
TV does not turn on, only standby access | I checked the power supply first, everything ok, secondary diodes, everything ok. bad flayback.. I changed the flayback, more vertical closed, replaced ci tda4865, changed the diodes, capacitors and resistors of the negative supply line of this ci and the 185v line | Replace of flyback + vertical output + capacitors diodes and resistors of the negative line of the tda8565 and the 185v line | Fenixtec |
| PHILIPS |
29PT4643/78
|
Dead power supply | D 6536 | Replace it | TIAGO.ELETRO |
| PHILIPS |
42PFL3604
|
Don't tune in | Bad selector/varicap. Note: tsound is no 33v power supply requested in the manual. | Replace selector/varicap | |
| PHILIPS |
42PFL3604
|
Does not turn on, stays on standby | Capacitor c806 sem carga. 4.7uf/400v | Replace the capacitor | LUCIO |
| PHILIPS |
20PT336A;78R
|
The filament turns on, gives a flash and turns off | 100uf25v and 1uf50v capacitors both power supply close to the 3540 trimpot | Replace both, both were dry, very low capacitance | janilson |
| PHILIPS |
14PT218A
|
Menu appears on the screen and does not obey commands | C 2006 with escape. the same is on pin 80 of the micro | Replace it or withdraw it | antonio vinicius alexandre nobrega |