Philips Repair Tips

Search: philips
Results: 14206

Make	Model	Symptom	Problem	Solution	By
PHILIPS	21PT5435	After being on for a while, it turns off.	If you've already done everything and changed what everyone said and it didn't work, disconnect pin 36 on the micro ehto and send the TV away.		CALIXSERVICE
PHILIPS	14GL1311	Low power supply, and it doesn't turn on.	Replace ts355 ,bc558.		This email address is being protected from spambots. You need JavaScript enabled to view it.
PHILIPS	20GX1659	Kind of out of tune	Change coil 5210		This email address is being protected from spambots. You need JavaScript enabled to view it.
PHILIPS	14PT314A/78R	It goes into protection in seconds, you have to insist to see the glow with a vertical stripe.	Micho latch on the trail with the vertical exit	Just scrape and solder the ci pins	alecio dal pozzo
PHILIPS	21PT6437	Dark screen, more with sound and characters.	R 3442 de 100k		This email address is being protected from spambots. You need JavaScript enabled to view it.
PHILIPS	21PT9467C78	Closed vertical. the deflection line at the top of the screen	Lack of negative voltage at the vertical output	Replace the resistor that feeds the negative voltage that comes from the fly back	This email address is being protected from spambots. You need JavaScript enabled to view it.
PHILIPS	20PT3331	TV inoperative with primary power supply ticking.....ticking....ticking...., but when using the heat steam station on the plate it worked, but when turning off the TV and it cooled down, it no longer turned on, So that's when I started looking for the defect in parts, it was when I threw heat on the photo-coupler and the TV turned on...	It was the photo coupler, because it had to be replaced and the TV worked normally		This email address is being protected from spambots. You need JavaScript enabled to view it.
PHILIPS	20PT120A	Doesn't start. When you activate the control, the LED flashes a few times and comes back on. all normal voltages.	Capacitor 2442 (smd) with cracked or damaged solder.		ECJ
PHILIPS	20PT524 L9.2A	Replace of the same	Q7400 bf 422 short base emitter	Replace of the same	This email address is being protected from spambots. You need JavaScript enabled to view it.
PHILIPS	15PT136A/00 ANUBIS A	Dark screen with sound	R 3296 (100Ω.) c.i. power supply tda 3504		Grobio
PHILIPS	21PT5432/78 PT	When it is on, it loses tune and comes back at the same moment and sometimes when it comes back on the image some characters appear as if it were resetting the memory.	Internally, the kinescope socket will spark, causing the computer to give a momentary breakdown.	Changing the kinescope socket is the same one used in Panasonic Philips tube devices	Helio Eletrosonic
PHILIPS	21PT5433	With characters but without image with sound	100k open resistor close to the flyback, r-3442		joelton
PHILIPS	20PT3331	TV with primary power supply chirping ticking......ticking.....ticking, and it didn't stabilize the voltage kept oscillating and wouldn't turn on	The integrated one that is below the board in the primary power supply, the tea 1506 t, was replaced	With the replace, the TV was clean and started working normally again, as a precaution, replace the capacitors and resolder the chassis ok thanks	HELIOMAR
PHILIPS	29PT4641/78	It makes it turn on but it doesn't turn on and when it turns on, colored lines appear at the bottom of the screen	C2484 de 10uf 100v e d6457 smd em curto no vertical	Replace	EletroClaudio Aguas Belas
PHILIPS	14PT3131	Cold turns on turns off several times warms up stays normal	Power supply coupler photo.		je_eletronica
PHILIPS	21PT9467C/78	Horizontal transistor was shorted. I put another one. When I turned on the flay back it kept beeping	I changed the flay back; and just run to the hug		DIEGO LIMA
PHILIPS	20PT4331	Keeps turning on and off with the vertical closed	Replacing the 3448/9448 resistor on the 180v line		VALDEMIR - NV ELETRONICA
PHILIPS	21PT9467	This TV arrived at my workshop with a burnt vertical ci, I replaced it but a resistor at the base of the ci was hot and with thin stripes on the TV screen	The vertical one was not the original	Putting the original vertical was normal, just run for the hug.	ozenildo
PHILIPS	29GX1899/78R	Stretched image/pulling to one color/taking time for the image to appear	Cap.elet.position 2431 (100mf x 200v) completely exhausted.	Replace the same.	jheliocavalcanti
PHILIPS	20PT529A	Turns off after a few minutes on	Cold solder on flyback negative	Re-weld the flyback	Filipe