Sharp Repair Tips
Search: sharp
Results: 1784
Results: 1784
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| SHARP |
C-14R12
|
Without characters closing the vertical and sometimes turns off when tuning | R671, r642, r665 open and d609 shorted, probably caused by oxidation at their terminals | Replace r671 from (27k), r 642 from (100k) r 665 from (150k) and d 609 from (1n4151). After the replace, the TV was ok. | GEORGE PONTES |
| SHARP |
C20R11
|
The image stopped outside the channel | Bobina aft | Break the internal capacitor, put a new 68 p one in place of the other one and run for a hug, brand new TV | fernando ferreira da silva |
| SHARP |
TVC 20S01 E 20R11
|
Image folded at the top | C508 (100µfx35v) | littlecarlos | |
| SHARP |
1467B
|
TV doesn't turn on, doesn't flicker | Ci vertical,diodo654,resistência655 | Hofman | |
| SHARP |
C20T51
|
Vertical closed | Replace ci vertical | Run for a hug | fernando |
| SHARP |
C-1417
|
Totally inoperative | Rah17, Rah18, Rah19, Rah0, Rahah, Rahah, Rahat, Rahah, Yesah01, Qah01 | c@rlinhoselectro | |
| SHARP |
C-14S02
|
Dead | C617 | RENATO | |
| SHARP |
C2053
|
Turning off when changing channels | C616 8n2 shorted | ||
| TVC-SHARP |
C-2013
|
TV sometimes the image disappears and tsound is no image for a long time, but it has sound, channels and high voltage. | This defect is caused by cold soldering of the h cable that leaves the main board and sends voltage to the trc filament. Resolder the cable h that creates filament tension. This defect is also characteristic of sharp and cold welds due to time of use. | BENICIO S. MADUREIRA | |
| TVC-SHARP |
C-2013
|
No audio, or sound sometimes fails | Cold solder on the cable that leaves the main board and goes to the speaker, close to IC 301, TDA 7056. Resolder it and everything works normally again. This simple defect is characteristic of Sharp as the solder breaks a lot due to time of use of the device. | BENICIO S. MADUREIRA | |
| TVC-SHARP |
C-2013
|
The TV turns on for 2 seconds to 4 seconds and turns off. | When you plug the AC cable into the socket, the TV turns on and off, and does not turn on again. But if you invert the AC cable position, the TV turns on and off as before. Don't have any doubts, disconnect the IC 501 vertical output pins and the problem will be solved. a small internal short in the ci tda3653b makes the horizontal oscillation disappear. also check c 504, but it is rare for it to fail. tsound is a check for the trc board socket, as this socket breaks the pin that connects to the screen due to time of use, it is cheap to change -o. another tip this defect looks like a horizontal output transistor with leakage or open flyback or IC 8380a internal defect, do not replace them, as the defect is ONLY in IC 501. | BENICIO S. MADUREIRA | |
| SHARP |
C-1417
|
Does not turn on, dead power supply, making noise | C 721 carbonized(10nf) | Manoel | |
| SHARP |
C14R12
|
TV does not generate horizontal | Shorted vertical output | La7830 was replaced and the TV became filler. | Antonio do radio Frores |
| SHARP |
C 14R12
|
Reduced frame and secondary power supply oscillating obs the frame is also oscillating | Ic 703 (se 115) with problems and also c 616 (6n8) with altered capacitance | Substituir ic 115 e c 616 | GEORGE PONTES |
| SHARP |
C-2038
|
Sometimes it turns on, and activates the protection on pin 50 of the tda 8841, referring to +180 v. the device turns off | Capacitor poliester, c-606, no horizontal. | CLAUDIO RIBEIRO - TECNOSAT ELETRONICA-JATAÍ-GO. | |
| SHARP |
C2057
|
Vertical stretched | Ic203 regulator +33v open | RETEC | |
| SHARP |
C-1491B
|
Horizontal partially covered by black band, only about 20% of image on the left side. | Rahah d aqs crossed. | Replace of r727. | MACC Eletrônica |
| SHARP |
C2999
|
Buzzing sound more noticeable in AV and at low volume | Lack of grounding | Grounding the sound output heatsink, for the seletronic, use a thick plate or wire harness. | ARS |
| SHARP |
C-2053
|
Pacifier clicks when replacing trans horiz 2sd1554 and turning it on. | Capacitor at c616- 8n2 1k6v entre pino 1 do fly-back e q602 | Replace without testing for the same or 822j 1k6v | MANTENOPOLIS |
| SHARP |
C 20R11
|
Turns on, after some time of operation it turns off and turns on again and so the time decreases until it no longer turns on | STK 73907 power supply regulator with problem. Note: all power supply secondary voltages work normally | Replaced the regulator and the TV was ok. | George Pontes |