Search: sony
Results: 20088
Make Model Symptom Problem Solution By
SONY N160A003L
Turning off as soon as it turns on Broken track between q802 and r808 DEO ELETRÔNICA
SONY ADP-200ER AA
Just secondary primary power supply zeroed out without any intention Open r1, open t1 driver and the q9 Obs. replace the q9 without measuring as it performs well in the test DEO ELETRÔNICA
SONY ADP-200ER AA
Only primary power supply without secondary R184 open or altered remove and measure outside the circuit It is a 7.5k smd 85b DEO ELETRÔNICA
SONY ADP-200ER AA
It has 5v from stand by and 5v from detect, but when the power supply is activated, all voltages die. Broken trail in primary Sound goes from r18 to q3 DEO ELETRÔNICA
SONY HCD-GPX8G
Enters protect 06. related to ventilation Vitrify resistors in the "-fan" . tsound are 4 resistors. 3 of 3r3 and 1 of 2r2. giving a final value of 3r. they are smd. put 1 of 5r6 and 1 of 6r8 in parallel and you will have the 3r. Jocimar
SONY HCD_GPX8G
Enters protect 06. related to ventilation Vitrify resistors in the "-fan" . tsound are 4 resistors. 3 of 3r3 and 1 of 2r2. giving a final value of 3r. they are smd. put 1 of 5r6 and 1 of 6r8 in parallel and you will have the 3r. Jocimar
SONY KDL-50W805B
Doesn't start Blinks LEDs this tip is only for the kdl-50w805 b Check capacitor disco c6524 short -> 22micro x 6.3v near usb connector oskarala
SONY KDL-50W805
Does not turn on, LEDs blink Short on main board Check capacitor disco c6524 short -> 22micro x 6.3v near usb connector oskarala
SONY ADP-200ER AA
Turning on the lamp in series identifying the short but you can't find the short on the board It can go directly to q9 (3n62k3) as it has a leak and I only opened the short with the board energized Just replace the Q9 and run for the hug DEO ELETRÔNICA
SONY ADP-240AR AA
Turn it on normally using the jumper, but when you inject something to work on the 12v output, the power supply dies The relay does not hold, it opens as soon as it ejects It was just replacing the ic41 (1608b) DEO ELETRÔNICA
SONY MHC-EC68USB
All functions locked Some keys leaking or shorted Replace all keys DEO ELETRÔNICA
SONY ADP-200ER BA
Giving 9v and varying the saying of 12v Photo coupler ic51 DEO ELETRÔNICA
SONY ADP-200ER BA
12 volt output oscillating a lot Driver com broblema Replace the same (reference t2) DEO ELETRÔNICA
SONY KV-29FX20E
FE1A
Works for a while and then goes off, blinks twice Ph 601 tcet1103g rusty between pines ANTMACARICO
SONY KDL-40BX425
Green LED lights up then flashes red, without 12v and 24v 15v zd971 with leakage Replace diode Cleiton
SONY KDL.. W955A
Turns off and flashes 4x Leak in the LED bus/or defect in the inverter Remove Q4001 (SMD switch) from the inverter board and close pins 4 and 5 of the CN2001 connector (which goes to the power supply) Elias Florencio
SONY KDL-48W655D
Does not turn on, standby LED flashes red 6 times Processor bga solder Reballing GABSENS
SONY FH-G88AV
Turns on, no sound, graphic bars do not work, noise when increasing or decreasing the volume Regulator IC1003 of 7v with 0v at the output, changing it, the device does not turn on anything, the regulator heats up until it burns again. Ic 901 defective. ci of digital volume. replace of 7v regulator ic-1003 and ic-901 m-62427fp device works perfect again Josimar Afonso
SONY KDL40BX425
When the TV turns on, the power on light turns on (green LED). It has no functions and if it turns off, it doesn't turn on again and most of the time it doesn't even light up the standby LED. Just unplug it. Ci u 701 changed. It has to be 3v3. Replaced the ci u701. the problem was solved. DANGRA ELETRÔNICA - SÃO PAULO
SONY ADP-160AR AA
Without 12 volts When you turn on the power supply, it goes up to 5v Ic 81 ( das2 ) DEO ELETRÔNICA