Sony Repair Tips
Search: sony
Results: 20088
Results: 20088
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| SONY |
KDL48W655D
|
LED blinking 5 times and won't turn on - two TVs with the same defect! | After several tests with two TVs and the same defect, I found that one LED on each TV took too long to turn on. | I replaced the bus with the problem and the defect disappeared. I would like to point out that when testing with the LED tester it was not possible to identify the defect, only by opening the TV. | Eletrônica JJ |
| SONY |
MHC-GP3G
|
Entering protect e04 | Defect in ic1405 njm2903v | Replace the same | barbadinha |
| SONY |
KDL-32R485A KDL-40R485A KDL-46R485A
ITC2 |
TV turns off by itself and standby LED blinks 6x. | Defect in the ci bd9397efv responsible for the backlight operation. In my case, I redid the connectors on the rulers, but the TV still activated protection. | Check the remaining voltage on the negative of the LED banks. the correct thing is to have between 0.8v and 1.5v left. Above that, the TV can trigger protection. If tsound is no defect in the rules, replace the ci. | rafaelmoraes99 |
| SONY |
MHC-GPX7
|
It doesn't turn on anything, not even stand-by. | Power supply apparently ok, with a voltage of 7v (stand-by voltage). the problem was in the ac-det line (sector that informs the computer that tsound is ac voltage coming from the primary). In my case, it was a defect in the power supply's PC702 photocoupler, which was not activating the base of the Q702 transistor (SMD connected to pin 3 of the power supply's CN3 socket) | Replace the pc702 photocoupler that goes into the power supply (if the base of the transistor q702 becomes polarized, the problem has been solved) | Gênios Eletrônica SJ SC |
| SONY |
KDL-46EX405
|
TV turns on, the logo appears, turns off and starts all over again | Smd capacitor near the i.c. 9301, close to cn 2600 | The capacitor was shorted, tsound are two more in parallel. | Ricardo Fortes |
| SONY |
KDL-46EX405
|
TV turns on, the logo appears, turns off and starts all over again | Smd capacitor near the i.c. 9301, close to cn 2600 | Ricardo Fortes | |
| SONY |
HCD EX8
|
Falls into disrepute and doesn't start. | Secondary power supply diode d 018 open | Replace d018 | Jsf |
| SONY |
KDL-32BX325
|
TV turns on whenever it wants | Power supply voltages ok, but on the main board, the u701, which is a 3.3v regulator, had a low voltage (1.3v). it was just a matter of changing and running for the hug. | ||
| SONY |
KV-29FA210
BA-5D |
Dull, increasing screen gives retrace lines. | Resistor 33k aberto r547 | Resistor replaced and defect corrected. | Tarcisio Brito |
| SONY |
KDL-46R485A
1-888-722-12 |
Completely off, no standby | Shorted capacitor close to the ic4000, it is the one closest to the edge of the board. With the short, he also blew fuse f4000. As I didn't have this fuse, I replaced it with a ferrite inductor (fb) from scrap metal. | Be very careful because on the first attempt to repair this capacitor I replaced it with a 47μF/25v electrolytic and it didn't work. Only when I replaced it with another one larger than 100μF/25v did the board turn on standby. Furthermore, be careful when choosing the capacitor because the supply voltage is high (19v). The board's architecture is very good, it's every technician's dream since each subcircuit has a fuse, making it much easier to locate the defect. | 2000 |
| SONY |
KLV40M400A
|
When turning on the TV, the LED button lights up green, then turns red and flashes 6 times | Backlight error: short in capacitors parallel to ci 6702 on the power supply board (capacitors c6732 ceramic, c6759 electrolytic, c6753 electrolytic | I replaced them and the RV returned to normal | magaivereletronica |
| SONY |
KDL-32R435A
|
4 blinks 8817 client | Tsound is a lack of 12 v that powers the screen, tsound may be a short on the 12 v line as well 8817 customer | Replace of ic6007 8817 client | marcos melo cascavel ce |
| SONY |
KDL32EX355
|
Shaking image | Replacing resistor on the vcon rd14 board | Placed a 1k resistor without success, placed 100r, solved | ANTENISTA |
| SONY |
KDL-52EX705
|
Turns on and then turns off and indicates error 6 (back light error) | Bad power supply (changed power supply) | 500ma fuse open, it was replaced and it didn't solve it, I checked the LEDs and they were fine, the LED voltage was 180v and it didn't stabilize, I spent a lot of time on this power supply and I didn't resolve this defect, if a friend knows anything related to this defect and just contact us by email, thank you | Alex Lopes |
| SONY |
KLV-32M400A
|
Does not turn on, LED flashes 3 times | F4001 e ic4001 | The fuse blew immediately and tsound was no short in any component. changing ic4001 solved it. | André |
| SONY |
KDL-46NX700
|
No picture, no backlight | F smd jl6020 na psu | ERP-ASSIST | |
| SONY |
32U4000
|
It lights up a few times but, when it comes on, it goes out almost immediately, leaving the red LED flashing | The problem is with the lamps. place a diode between pin 17 and ground of the bd9897fs ci, this procedure eliminates the integrated protection and makes it possible to check or, even with lamps with problems, it remains working | Mário Santos | |
| SONY |
KV-M1440E
|
It starts to get dark after a while. it even stops having an image. | Leaky d302 diode | Swap .. equivalent 1n4148 | Marco Marques |
| SONY |
KDL-32U2000
|
Image appears for a few seconds with sound and then the image fails and the sound is ok | Failure of one of the lamps | Alonso | |
| SONY |
KDL-46W4500
|
Does not turn on, no voltage reaches the rectifier bridge | Thermal fuse rwt05 6.8ω/142ºc open | Replace for an identical r of 6.8ω and a thermal of 142º in series | C. Santos |