Sony Repair Tips
Search: sony
Results: 20100
Results: 20100
Make | Model | Symptom | Problem | Solution | By |
---|---|---|---|---|---|
SONY |
KV-29FS100
|
Does not turn on, the LED flashes 9 times, and returns to standby and repeats the cycle several times. | Resistor r693 330k close to the power supply relays. | Replace r693 in the power supply. | Marcones de Araripina PE. |
SONY |
HCD-EX6
|
When I plugged the sound into the socket it would turn on and off, only the times I turned it on, neither the CD nor the USB would work. | After analysis I found the diode d400 1n4002-a2 which is on the panel PCI it was open, after replacing the sound it works normally again. | Jonas | |
SONY |
HCD-EX6
|
Turned off in 3 seconds | Defect in the CD part, when I disconnected the flat cables it stopped turning off | Jonas | |
SONY |
HCD-EC59
|
Protect | Q619- main power on-off | Replace q619--2sc3052f | EMERSON RIBEIRO |
SONY |
HCD-SH2000
|
No sound/Audio, does not arm protection/protect, displays please wait when activating USB or CD. | Tsound is no 9V power supply for the IC500 audio processor or the 4558 preamps. | Transistor q800 and c754 short, resolved by replacing them. | EduSSantoz |
SONY |
HCD-GTX88
|
Does not come out of standby | X402 bad 5mhz crystal, just change it (it was measuring around 2.065 k from one end to the other, that is, leaky). | Ronaldo Vieira | |
SONY |
KDL40BX455
|
TV turns on red LED lights up turns green and turns back to red and flashes | R 9810.... 9811... 9812 remove and scrape the glue underneath | RJ ELETRONICA | |
SONY |
KDL40BX455
|
TV turns on red LED lights up turns green and turns back to red and flashes | R 9810.... 9811... 9812 remove and scrape the glue underneath | RJ ELETRONICA | |
SONY |
KLV-40S200A
|
When turning on the TV, the LED flashes 4 times, no image, no sound. | Replacement of fuse f401 - 10a on the inverter board on the left side of the TV | Replacing the fuse on the inverter left upper board f401 10a | Ferrarini |
SONY |
KDL-55W805C
|
Turns on, the back light comes on, the Sony logo appears, then turns off and the stand by LED flashes 3 times | Shorted smd capacitor next to the ic 8000 close to the cn8001 connector | Replace it or leave it without a capacitor | Alex Lopes <small> |
SONY |
40EX455
|
Sony appears and turns off | See q6101, q6102 and r6536 and this electrolytic capacitor on the 5 v line c9305 | ADAILTON | |
SONY |
40EX455
|
Sony appears and turns off | I replaced all the photocouplers and resoldered all the cis smd and it solved the problem. | FERNANDES | |
SONY |
KDL-40HX755
|
TV flashes red LED but not in the image, the TV is on if you loosen the tcon cable it doesn't turn on it only flashes LED 5x saying tcon error | Changing tcon didn't work, on the main board tsound are some 4 in 4 coils right in the connector that goes to t com. one had broken.. I made a jump and it turned on ^_^ | Alexandre | |
SONY |
KV140-MG
|
Doesn't start | Q602 and q603 in the power supply shorted. | Replace q602 and q603 (2sc4834) | MARCONES DE ARARIPINA-PE |
SONY |
MHC-GRX9900
|
Display lights up very weakly | All micro and display voltages are correct | Sebastião | |
SONY |
MHC-GTR6 GTR8H
|
Turns off and LED flashes | Fault on the thermal detect d1310(maz8091) dz9.1v line, you can put dz10v. | samuel leite | |
SONY |
DZ-295
|
Does not turn on display off power supply ok and display too | Lack of voltage ever 3.3 =e3.3v | Look for the diode d503 it receives 4v and releases 3.3 I replaced it and the problem was resolved. | FLIPFLOP |
SONY |
HCD-EX660Z
|
Goes into protection after a few seconds | Solution is to change the sound output IC | Replace the sound output, remove it from the power supply and you can hear the sound on the headphone input directly from the pre | |
SONY |
KLV-37NL14A
|
Turns on and then turns off by flashing red LED 6 times | In my case it was a fuse on the reverse board, position f1, close to the middle screw | Note: this TV has two versions. the invert plate for this is "fr-4-86-py" | Mario Moreci |
SONY |
KDL32R305
|
It turns on, then makes noise and turns off and flashes 6 times, after changing the LED bars it was the same thing, because when changing new bars you have to solder the bar fittings as they give very poor contact and represent a defect on the board | Weld bars one by one into the fittings | LORD |