Search: sony
Results: 20072
Make Model Symptom Problem Solution By
SONY KDL-40BX425
Does not show voltage 12-24 volts flashes twice. Leaky transistor q931 and faulty ic 902. eletrofepar
SONY 32R435A
Does not turn on the standby Shorted capacitor on the right side of the crystal just above the medi/tek processor Check if it is getting hot with your fingertip. Mariano
SONY KDL-32EX525
TV doesn't turn on, doesn't even show LED STBY 1) capacitor shorted on the tcom throwing the 12v to gnd, incredible because the tcom fuse didn't burn, it burned one of the power mosfets on the power supply board (q6410 - it's an 8118) leaving the tcon_vcc_12v connected directly. 2) after repairing the power supply board, the TV still wouldn't turn on. the 3.3v stby voltage was ok, but the stby led did not light up. I checked that the board has a 1.2v stby regulator that was without voltage, I removed the regulator and 4 capacitors from the line but none of them were shorted, I tried feeding the main board with 3.3v and 1.2v from a power supply. bench but the LED didn't light up. When I connected 1.2v from the power supply to the line, initially tsound was a short, I slowly released the current, increasing the voltage to check wsound the short was and suddenly the short disappeared. Apparently the short was inside the main IC of the board, when I released the current on the 1.2v line, what was shorted inside the IC burned and released the short. just changing the main board. 2000
SONY MHC-EX88
MHC-EX88
Low sound It is inoperative without 6v pins 3.5 of ics 600 and 601 Replace c612 100mf/10v short MEKCORADIO
SONY KDL40BX425
TV kept appearing on the screen, warning pen driver connected. Ci that is behind the u112 usb input with 5-pin smd leak.ci Replace ci u112 Eletrônica Moisés
SONY 40BX425
The stand by doesn't turn on, it doesn't turn on, but it has 5v from the power supply Ci 701 regulator 3.3 v Mariano
SONY KDL40BX425
It kept appearing on the TV screen, warning that tsound was a pen driver consuming energy. Change the 5-legged ci, behind the usb input. Eletrônica Moisés
SONY KDL-46R485A
Does not turn on, LED flashes 5x I isolated the faulty display side (I removed the flat that connects the two sides of the display) feeding it with an external power supply I threw 10v at the avdd, ca30 started to smoke I removed it, the TV turned on, perfect image. Maurilio
SONY KLD 32R305
Turn on and off 3 times Bad led bar Customer in a hurry, a 32-inch Samsung bar was adapted and it worked
SONY KDL-46R485A
No standby signal The larger smd capacitor close to ic6004 was shorted, f6002 open Replace capacitor and smd fuse Jamis
SONY KDL-40BX455
Turns on, red LED lights up, then green LED and returns to standby, red LED flashing 6x. High voltage transformers changed on the driver board. one leaking loudly and the other open. Replace transformers t109, t110. Arock
SONY KDL46EX725
Does not turn on red LED blinks twice, sometimes turns on after several attempts. On the power supply board, locate 2 mega resistors, scrape the glue underneath all of them. Carlossbs
SONY MHC-GTX787
Only turned on with remote Change all micro keys. Luciano
SONY HCD GTZ-2
Blinking LED does not turn on Q 903 transformer plate Damíão
SONY MHC-GPX77
Protect e03 Resolder the following: ic1000/1007/1009/1010 on the amplifier pci I cleaned it and used the rework station on this circuit and it worked. Medeiros / Barbacena MG
SONY CECH-4003A
PS3
Does not synchronize control 1.8 module power regulator. Tsound was 3v at the regulator output. david rayel
SONY KDL32EX405
When activated, the red LED turns to green and back, sometimes it flashes 3 times Shorted capacitor next to the usb connector tsound are 2 capacitors, one altered and the other shorted Both are on the ci side and are on the usb side
SONY GRX500 GRX700 GRX800
Sem display Broken track on traffic sign I did the trail with wire Gianluca
SONY KDL-46EX655
The image does not turn on, the LED blinks 3 times, sometimes 8 blinks Hdmi ci short Ci of varicap or network causes the same problem eletrozica
SONY PL43F4000AGXZD
Does not turn on, the red LED flashes 3 times (stand-by/protection code) (q5014 - fgd4536 shorted) (d5057- sf104400hd shorted) (q5000 - rjp63k2 shorted) (c5078 (popped) - 331k) (c5075 - 102k value changed) (c5128 - 102k value changed) Replace them all FridayTechLab.