Sony Repair Tips
Search: sony
Results: 20088
Results: 20088
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| SONY |
CCDTR44
|
Eats tapes (found tension spring, ref. 781, had come loose) | Unit eats tapes. found problem to be caused by tension spring,ref. 781, coming loose. | ||
| SONY |
CCDTR44
|
Dead (found poor soldering on cn003 on dd-80 mcb) | Unit was dead (would not even eject). found problem to be caused by poor soldering of cn003 on the dd-80 mcb. | ||
| SONY |
CCDTR44
|
Ejects immediately after loading (ref # 752 was dislodged) | Immediately after loading a tape, the unit would eject thetape. found that the exit guide, ref. # 752, had come out of the track. | ||
| SONY |
CCDTR44
|
Won't load tape (found drum would not rotate; replaced drum) | Unit would not load tape. found that the drum had a tightspot which prevented it from rotating. | ||
| SONY |
CCDTR44
|
No rew or review, noise in play (magnet on reel came loose) | The unit had no rewind or review. noise could be heard duringplay. found problem to be caused by the magnet on the supply reel comingloose. | ||
| SONY |
CCDTR44
|
Dead (found loose connector between power mcb & main mcb) | The unit was dead found a loose connector between the powerboard and the main board. | ||
| SONY |
CCDTR44
|
Won't stay in record (found mode switch in wrong position) | Unit would not stay in record when the start/stop button waspressed. found that the start/stop mode select switch was set in theposition which allows recordings to be made only while the start/stopswitch is held in. this is an operational feature of th | ||
| SONY |
CCDTR44
|
Dead (found battery contact j001 on dd-80 mcb cold soldered) | Dead. found battery contact j001 on dd-80 mcb was coldsoldered. | ||
| SONY |
CCDTR44
|
Won't thread (found high tape tension due to ref 769 loose) | Unit would not thread tape. found problem to be caused byratchet tension spring (ref. 769) coming dislodged from at the chassisend. | ||
| SONY |
CCDTR400
|
Int. dead, shut down, lockup (found bad solder on cn203) | An asc reported that the unit had intermittent functions, orwould shutdown or lock up. problem was found to be caused by poor solderon cn203. | ||
| SONY |
CPD17SF2
|
Defective horizontal output transistor q507 | 3 units came in with same problem, defective horizontaloutput transistor q507 872982107. | ||
| SONY |
CPD17SF2
|
Shuts off after 2 seconds | Monitor will shut off after 2 seconds. found 12v dc out ofregulator ic602 low (about 6vdc) troubleshoot to hybrid ic pm501. pins 1& 2 were shorted, which caused overload of ic602. | ||
| SONY |
CPD15SX1
|
Changing logic pcb | Installing new logic pcb causes a different problem thanoriginal symptom. power up and led blinks. micro download gives nocommunication with monitor. | ||
| SONY |
CPD15SX1
|
Insufficient horizontal width | Monitor came in dead. after replacing q301 horiz. outtransistor phuc found that the horizontal width was not sufficient andcould not be adjusted. | ||
| SONY |
CPD15SX1
|
Defective video output ic501 | Set came in with no power. discovered defective ic501 onvideo board. ic501 pin 2 was shorted to ground overloading the 12v line. | ||
| SONY |
CPD15SF2
|
No auto degauss | Power up unit and it will not auto degauss. found q601relay drive transistor not turning on. q601 ok found pin 21 of ic901 hadno output. | ||
| SONY |
CPD15SF2
|
Defective ic001 on a board | Seeing a problem with cpd15sf2. tech reported 3 failures ofic001 in last week. unit had no video output from this rgb preamp ic. | ||
| SONY |
CPD15SF1
|
Intermittent on and off | Set came in with intermitent on and off, burning smell, andno power. | ||
| SONY |
SLV960HF
|
Different power supply unit | Starting at serial number 102111, this model will have a different power supply unit for which the schematic is not available yet. the new power supply is backward compatible with the original one. a supplement will be is | ||
| SONY |
SLV780HF
|
Won't record or pb stereo - tape path adjustment | Won't record or playback stereo. |