Sony Repair Tips
Search: sony
Results: 20073
Results: 20073
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| SONY |
CCDTRV21
|
Dead (found battery contacts not extending thru cabinet) | The unit had no power. found problem to be caused by thebattery contacts which were not extending through the cabinet, whichprevented contact with the battery. | ||
| SONY |
CCDTRV21
|
No speaker audio (found open l304 on cf-42 mcb) | Unit had no speaker audio. headphone and line-out audio wereo.k. found l304 on the cf-42 mcb was open. this resulted in 2.4 vdcappearing on pin 16 of audio amp ic651, rather than the 4.7 vdc noted onthe schematic. | ||
| SONY |
CCDTRV21
|
Dead, but unit draws .25 amps consantly (found x400 bad) | Unit appeared dead. however, it was constantly drawing .25amps from an external power supply. this current draw was found to becaused by mode control ic303 always outputting the vtr d-d on signal, butthere was nothing wrong with ic303 itself. problem | ||
| SONY |
CCDTRV11
|
Dead (found battery was only inserted to first latch point) | No power. found that the problem was caused by the batterynot being fully secured to the camera. this year's models have a newlocking mechanism which actually has 2 points at which the user will feela latched-in condition. the contacts of the battery | ||
| SONY |
CCDTRV11
|
Dead (found major short on dc-dc converter mcb blew f002) | No power. found that a major short on the dd-80 mcb wascausing f002 to blow. | ||
| SONY |
CCDTRV11
|
Dead (found battery contacts not extending thru cabinet) | The unit had no power. found problem to be caused by thebattery contacts which were not extending through the cabinet, whichprevented contact with the battery. | ||
| SONY |
CCDTRV11
|
No speaker audio (found open l304 on cf-42 mcb) | Unit had no speaker audio. headphone and line-out audio wereo.k. found l304 on the cf-42 mcb was open. this resulted in 2.4 vdcappearing on pin 16 of audio amp ic651, rather than the 4.7 vdc noted onthe schematic. | ||
| SONY |
CCDTRV11
|
Dead, but unit draws .25 amps consantly (found x400 bad) | Unit appeared dead. however, it was constantly drawing .25amps from an external power supply. this current draw was found to becaused by mode control ic303 always outputting the vtr d-d on signal, butthere was nothing wrong with ic303 itself. problem | ||
| SONY |
CCDTR99
|
Dead (found battery was only inserted to first latch point) | No power. found that the problem was caused by the batterynot being fully secured to the camera. this year's models have a newlocking mechanism which actually has 2 points at which the user will feela latched-in condition. the contacts of the battery | ||
| SONY |
CCDTR98
|
Dead (found battery was only inserted to first latch point) | No power. found that the problem was caused by the batterynot being fully secured to the camera. this year's models have a newlocking mechanism which actually has 2 points at which the user will feela latched-in condition. the contacts of the battery | ||
| SONY |
CCDTR94
|
Dead (found battery was only inserted to first latch point) | No power. found that the problem was caused by the batterynot being fully secured to the camera. this year's models have a newlocking mechanism which actually has 2 points at which the user will feela latched-in condition. the contacts of the battery | ||
| SONY |
CCDTR94
|
Dead, but unit draws .25 amps consantly (found x400 bad) | Unit appeared dead. however, it was constantly drawing .25amps from an external power supply. this current draw was found to becaused by mode control ic303 always outputting the vtr d-d on signal, butthere was nothing wrong with ic303 itself. problem | ||
| SONY |
CCDTR91
|
Unit stuck in service mode, but data is ok (found vc132 bad) | Vc132 board was bad, and found power switch corroded under theshield. unit was stuck in service mode, but data was normal. when youturn off standby switch, the vtr is still on. | ||
| SONY |
CCDTR91
|
Appears to be in forced power mode but isn't (vc132 was bad) | Unit seems to be in forced power mode (cam & vtr). by viewingthe lanc jig, you will see vtr/camera both on. on page d, address 21the data is 00 (normal). the mode control ic is ok. isolated problem tovc132 board. | ||
| SONY |
CCDTR88
|
Dead (found battery was only inserted to first latch point) | No power. found that the problem was caused by the batterynot being fully secured to the camera. this year's models have a newlocking mechanism which actually has 2 points at which the user will feela latched-in condition. the contacts of the battery | ||
| SONY |
CCDTR84
|
Dead (found battery was only inserted to first latch point) | No power. found that the problem was caused by the batterynot being fully secured to the camera. this year's models have a newlocking mechanism which actually has 2 points at which the user will feela latched-in condition. the contacts of the battery | ||
| SONY |
CCDTR84
|
Dead, but unit draws .25 amps consantly (found x400 bad) | Unit appeared dead. however, it was constantly drawing .25amps from an external power supply. this current draw was found to becaused by mode control ic303 always outputting the vtr d-d on signal, butthere was nothing wrong with ic303 itself. problem | ||
| SONY |
CCDTR814
|
Dead (found battery was only inserted to first latch point) | No power. found that the problem was caused by the batterynot being fully secured to the camera. this year's models have a newlocking mechanism which actually has 2 points at which the user will feela latched-in condition. the contacts of the battery | ||
| SONY |
CCDTR78
|
Dead (found battery was only inserted to first latch point) | No power. found that the problem was caused by the batterynot being fully secured to the camera. this year's models have a newlocking mechanism which actually has 2 points at which the user will feela latched-in condition. the contacts of the battery | ||
| SONY |
CCDTR74
|
Dead (found battery was only inserted to first latch point) | No power. found that the problem was caused by the batterynot being fully secured to the camera. this year's models have a newlocking mechanism which actually has 2 points at which the user will feela latched-in condition. the contacts of the battery |