Sony Repair Tips
Search: sony
Results: 20088
Results: 20088
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| SONY |
CCDTR64
|
Dead, but unit draws .25 amps consantly (found x400 bad) | Unit appeared dead. however, it was constantly drawing .25amps from an external power supply. this current draw was found to becaused by mode control ic303 always outputting the vtr d-d on signal, butthere was nothing wrong with ic303 itself. problem | ||
| SONY |
CCDTR614
|
Dead (found battery was only inserted to first latch point) | No power. found that the problem was caused by the batterynot being fully secured to the camera. this year's models have a newlocking mechanism which actually has 2 points at which the user will feela latched-in condition. the contacts of the battery | ||
| SONY |
CCDTR600
|
Battery lock claw broken | Battery does not stay on. | ||
| SONY |
CCDTR6
|
If au-92 unavailable, au-51 can be used with minor changes | The unit had audio problems the au-92 board was no longeravailable. | ||
| SONY |
CCDTR54
|
Dead (found battery was only inserted to first latch point) | No power. found that the problem was caused by the batterynot being fully secured to the camera. this year's models have a newlocking mechanism which actually has 2 points at which the user will feela latched-in condition. the contacts of the battery | ||
| SONY |
CCDTR514
|
Dead (found battery was only inserted to first latch point) | No power. found that the problem was caused by the batterynot being fully secured to the camera. this year's models have a newlocking mechanism which actually has 2 points at which the user will feela latched-in condition. the contacts of the battery | ||
| SONY |
CCDTR500
|
Poor playback tracking (found bad solder & short on cn002) | Poor playback tracking. found cn002 on the vc-137 mcb looseand shorted. | ||
| SONY |
CCDTR5
|
No color e-e (found q182 shorted) | In e-e mode very weak color, almost no color. burst was goodat waveform monitor. | ||
| SONY |
CCDTR44
|
Dead (found battery was only inserted to first latch point) | No power. found that the problem was caused by the batterynot being fully secured to the camera. this year's models have a newlocking mechanism which actually has 2 points at which the user will feela latched-in condition. the contacts of the battery | ||
| SONY |
CCDTR44
|
Dead, but unit draws .25 amps consantly (found x400 bad) | Unit appeared dead. however, it was constantly drawing .25amps from an external power supply. this current draw was found to becaused by mode control ic303 always outputting the vtr d-d on signal, butthere was nothing wrong with ic303 itself. problem | ||
| SONY |
CCDTR40
|
Recorded audio is muted | Svcr. has unit that has muted mic audio. 5v is being appliedto pin 35 of ic601 (au171 board). if you remove voltage audio is fine.traced power supply of voltage back to pin 10 of ic158 (vs116 board). this isfader out. data comes through ic156 to control d/ | ||
| SONY |
CCDTR4
|
Camera has no video out, evf ok (found open ic201-8 to c207) | Unit has video in evf but no video out of pin 8 of ic201. | ||
| SONY |
CCDTR200
|
No pix in vf; vf56 damaged the crt | No pix in vf. used my test crt to isolate problem. foundthat the crt was bad. upon installing a new crt, it didn't work either.in fact, it also became physically damaged. found that the crts weredamaged because of the vf-56 board. | ||
| SONY |
CCDF302
|
No color in playback (found corrosion on va67 board) | Unit played back video in black and white. | ||
| SONY |
CPD20SF2
|
Unit in shutdown; loose shield | Unit turned on ok, then went into shutdown. failureinformation showed, no vert. retrace. removed main emi shield. ps shieldplate (item 64) was loose against n board. mounting screw was missing. | ||
| SONY |
CPD17SF2
|
Shutdown; power & saving led flash; geom led on | Unit shut down after hv came up. power and saving lightswere flashing. geom light was on. found q510 almost shorted (about 200Ω). | ||
| SONY |
CPD15SX1
|
Replacement logic board not compatible | Replaced logic board with new board. unit had no highvoltage and power light flashed amber. tried 12 boards in 2 unitswith the same symptoms. | ||
| SONY |
WMFS493
|
Low battery indicator constantly on | The e is constantly on even with new batteries. | ||
| SONY |
TAM1000
|
Keeps cutting off icm - remove solder short on ic306 | Cuts off first call and then it will not record any messageat all. | ||
| SONY |
MDR14
|
Part confusion | There is no part #s list for various styles of mdr 014headphone. mdr 14 with mini micro plug that goes to remote commander.some have regualr plugs, 1/8, with an l shape and some are straight. onsome the wires plug into the earphone (old style) and new |