Sony Repair Tips
Search: sony
Results: 20073
Results: 20073
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| SONY |
CDX65RF
|
Part availability: hideaway/wired display | The manual has no part number for hideaway units and wireddisplays that are defective and cannot be repaired to component level. | ||
| SONY |
CDX51RF
|
Part availability: hideaway/commanders | The manual has no part number for hideaway units and wiredcommanders that are defective and cannot be repaired to component | ||
| SONY |
CDX5090
|
Display indicator bad (found poor solder on cnp801) | The cdx5090 had a bad display readout. this was caused by abad solder connection on cnp801. this connector is located on the displayboard. | ||
| SONY |
CDX45RF
|
Part availability: hideaway/commanders | The manual has no part number for hideaway units and wiredcommanders that are defective and cannot be repaired to component level. | ||
| SONY |
CDX4090
|
Lights on display went out | The display board lamps (ref# pl801, pl802) went out, foundthe display board resistors (r825,r827) were over-dissipated. thiscaused the display board to become damaged. | ||
| SONY |
CDX3100
|
Loads disc, won't clamp (cleaned area between ref 161 & 159) | Would load disc, but not clamp it. found that the d-lever(ref. 161) was sticking, which prevented the tr circular rack gear toengage (this rack gear is not referred to in the service manual, but isatached to tr tension spring ref. 163). | ||
| SONY |
CDX2100
|
Loads disc, won't clamp (cleaned area between ref 161 & 159) | Would load disc, but not clamp it. found that the d-lever(ref. 161) was sticking, which prevented the tr circular rack gear toengage (this rack gear is not referred to in the service manual, but isatached to tr tension spring ref. 163). | ||
| SONY |
CCDV701
|
No record, looks like one channel bad (found q202 defective) | No record, looks like one head out. found pin 4 of hr10board good. at pin 24 of ic001 (on the hr10 board) the signal was good,but bad at pin 37. found q202 to test pin 204 shorted. | ||
| SONY |
CCDTR91
|
No focus, no zoom (found ps501 open) | Unit has no focus or zoom functions. | ||
| SONY |
CCDTR7
|
No e-e video (repaired open trace between r217 & d303 cath.) | No e-e video burst and sync ok. | ||
| SONY |
CCDTR65
|
No pb video (found ic158 on vs100 mcb bad) | No pb video audio ok. camera e-e ok. | ||
| SONY |
CCDTR5
|
Distorted evf pix; ee ok (found q230 on vs-22 mcb defective) | Evf pix extremely distorted ee pix ok. | ||
| SONY |
CCDFX730V
|
No video or distorted video (resoldered ic503) | Have seen a number of fx730v units with no video ordistorted video. problem involves solder connections around ic503. | ||
| SONY |
CCDFX710
|
Unit dead, f950 opens (edge of bracket shorted to fp607) | Unit would intermittently go dead, f950 would open. afterreplacing f950, unit would work ok again for a while, then f950 would blowagain. also found this problem on serial number 1010139. | ||
| SONY |
CCDFX640
|
Intermittent eject (resoldered ic503 and rb503) | Three main symptoms are: intermittent eject, dead, in e-elooks like character generator missing (only dots). mkt. 3/95 | ||
| SONY |
CCDFX640
|
No color in camera video (found l605 not secured to vc142) | No color in camera video. problem caused by l605 comingloose from board. l605 is a peaking coil in the chroma buffer amp. | ||
| SONY |
CCDFX640
|
Unit dead (resoldered ic503) | Unit dead on other cameras this may be intermittent power. | ||
| SONY |
CCDFX640
|
Int. pix/dead, other failures (resoldered cn504 & ic503) | Seeing a number of assorted failures involving poorsoldering on ic503/mode cpu and vs111 board connection cn504 whichconnects the dc-dc converter board/dd65. a unit may have one or more ofthe following symptoms:ic503 - poor soldering - intermittent pict | ||
| SONY |
CCDFX640
|
Appears to be stuck in record pause (reloaded default data) | Unit comes on in vtr mode. camera is also on. it appearsthat the unit is stuck in record pause. | ||
| SONY |
CCDFX340
|
Intermittent camera color (found poor solder, l605 on vc159) | Intermittent color from camera video. problem caused by apoorly soldered l605. l605 is a peaking coil in the chroma buffer q605. |