Sony Repair Tips
Search: sony
Results: 20073
Results: 20073
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| SONY |
CCDTR74
|
Dead, but unit draws .25 amps consantly (found x400 bad) | Unit appeared dead. however, it was constantly drawing .25amps from an external power supply. this current draw was found to becaused by mode control ic303 always outputting the vtr d-d on signal, butthere was nothing wrong with ic303 itself. problem | ||
| SONY |
CCDTR73
|
After changing drum, no pix | Unit had line in playback. servicer ordered a-7048-776-a andit was on b/o for 2 mos. drum was replaced by a-7048-823-a. servicersays unit has no rf output now and pin configuration on drum is different.could this be the cause of no rf output? see att | ||
| SONY |
CCDTR714
|
Dead (found battery was only inserted to first latch point) | No power. found that the problem was caused by the batterynot being fully secured to the camera. this year's models have a newlocking mechanism which actually has 2 points at which the user will feela latched-in condition. the contacts of the battery | ||
| SONY |
CCDTR70
|
No eject (found bad connections on vs112 mcb) | No eject. | ||
| SONY |
CCDTR64
|
Dead (found battery was only inserted to first latch point) | No power. found that the problem was caused by the batterynot being fully secured to the camera. this year's models have a newlocking mechanism which actually has 2 points at which the user will feela latched-in condition. the contacts of the battery | ||
| SONY |
CCDTR64
|
Dead, but unit draws .25 amps consantly (found x400 bad) | Unit appeared dead. however, it was constantly drawing .25amps from an external power supply. this current draw was found to becaused by mode control ic303 always outputting the vtr d-d on signal, butthere was nothing wrong with ic303 itself. problem | ||
| SONY |
CCDTR614
|
Dead (found battery was only inserted to first latch point) | No power. found that the problem was caused by the batterynot being fully secured to the camera. this year's models have a newlocking mechanism which actually has 2 points at which the user will feela latched-in condition. the contacts of the battery | ||
| SONY |
CCDTR600
|
Battery lock claw broken | Battery does not stay on. | ||
| SONY |
CCDTR6
|
If au-92 unavailable, au-51 can be used with minor changes | The unit had audio problems the au-92 board was no longeravailable. | ||
| SONY |
CCDTR54
|
Dead (found battery was only inserted to first latch point) | No power. found that the problem was caused by the batterynot being fully secured to the camera. this year's models have a newlocking mechanism which actually has 2 points at which the user will feela latched-in condition. the contacts of the battery | ||
| SONY |
CCDTR514
|
Dead (found battery was only inserted to first latch point) | No power. found that the problem was caused by the batterynot being fully secured to the camera. this year's models have a newlocking mechanism which actually has 2 points at which the user will feela latched-in condition. the contacts of the battery | ||
| SONY |
CCDTR500
|
Poor playback tracking (found bad solder & short on cn002) | Poor playback tracking. found cn002 on the vc-137 mcb looseand shorted. | ||
| SONY |
CCDTR5
|
No color e-e (found q182 shorted) | In e-e mode very weak color, almost no color. burst was goodat waveform monitor. | ||
| SONY |
CCDTR44
|
Dead (found battery was only inserted to first latch point) | No power. found that the problem was caused by the batterynot being fully secured to the camera. this year's models have a newlocking mechanism which actually has 2 points at which the user will feela latched-in condition. the contacts of the battery | ||
| SONY |
CCDTR44
|
Dead, but unit draws .25 amps consantly (found x400 bad) | Unit appeared dead. however, it was constantly drawing .25amps from an external power supply. this current draw was found to becaused by mode control ic303 always outputting the vtr d-d on signal, butthere was nothing wrong with ic303 itself. problem | ||
| SONY |
CCDTR40
|
Recorded audio is muted | Svcr. has unit that has muted mic audio. 5v is being appliedto pin 35 of ic601 (au171 board). if you remove voltage audio is fine.traced power supply of voltage back to pin 10 of ic158 (vs116 board). this isfader out. data comes through ic156 to control d/ | ||
| SONY |
CCDTR4
|
Camera has no video out, evf ok (found open ic201-8 to c207) | Unit has video in evf but no video out of pin 8 of ic201. | ||
| SONY |
CCDTR200
|
No pix in vf; vf56 damaged the crt | No pix in vf. used my test crt to isolate problem. foundthat the crt was bad. upon installing a new crt, it didn't work either.in fact, it also became physically damaged. found that the crts weredamaged because of the vf-56 board. | ||
| SONY |
CCDF302
|
No color in playback (found corrosion on va67 board) | Unit played back video in black and white. | ||
| SONY |
CPD20SF2
|
Unit in shutdown; loose shield | Unit turned on ok, then went into shutdown. failureinformation showed, no vert. retrace. removed main emi shield. ps shieldplate (item 64) was loose against n board. mounting screw was missing. |