☰

Sony Repair Tips




AIWA
BEKO
CCE
CINERAL
DAEWOO
FUNAI
GRADIENTE
GRUNDIG
HITACHI
ITT
JVC
LG
MITSUBISHI
PANASONIC
PHILCO
PHILIPS
PIONEER
RCA
SAMSUNG
SANYO
SHARP
SONY
THOMSON
TOSHIBA
VESTEL


Search: sony
Results: 20073
Make Model Symptom Problem Solution By
SONY MHCC405SS
Won't spin disc or focus - unjam optical block assy The unit will neither spin the disc or perform focus search.
SONY MDS535
No audio left channel in record mode - repl ic671 No audio left channel when recording. found ic671 linebuffer shorting the input audio to ground.
SONY HCDD550
Intermittent sound on all modes - resolder r1200 pwr amp bd Unit cuts off and on after a time. found r1200 on power amplifier board not soldered to board.
SONY CDPCX153
Mechanical ticking while playing cd's - adj holder clamp asy Ticking noise while playing cd's (intermittant scraping). thisdoesn't happen all the time sometin=mes the unit could play for an hourbefore the noise is heard.
SONY CDPCX153
No display - broken taxes on display board # 69 No display.
SONY CDPCX153
Disc is scraping on chucking assy when playing The disc may be scarping on chucking assy when playing.
SONY CDPCA7ES
Tray motor not labeled or wired correctly After replacing the tray motor with a new one the playerwould not work correctly, the tray would rotate back and forth and notrecognize the cd in the unit.
SONY CDPCA7ES
Will not load, no platter rotation - replaced m801 Units exhibit a variety of loading symptoms. all are dueto the rotary table not turning. problem is caused by rotary table motor, m801.
SONY CDPC90ES
Not reading cd's intermittently - replaced d601/602 Unit would not read cd's intermittently, and would damagecd's. found unit would intermittently not see that there was a disc. thiswould happen particularly in discs 1,2 & 10.
SONY CDPC545
Tray motor not labeled or wired correctly After replacing the tray motor with a new one the playerwould not work correctly, the tray would rotate back and forth and notrecognize the cd in the unit.
SONY CDPC445
Tray motor not labeled or wired correctly After replacing the tray motor with a new one the playerwould not work correctly, the tray would rotate back and forth and notrecognize the cd in the unit.
SONY CDPC435
Tray motor not labeled or wired correctly After replacing the tray motor with a new one the playerwould not work correctly, the tray would rotate back and forth and notrecognize the cd in the unit.
SONY CDPC335
Tray motor not labeled or wired correctly After replacing the tray motor with a new one the playerwould not work correctly, the tray would rotate back and forth and notrecognize the cd in the unit.
SONY CDPC245
Tray motor not labeled or wired correctly After replacing the tray motor with a new one the playerwould not work correctly, the tray would rotate back and forth and notrecognize the cd in the unit.
SONY CDPC235
Tray motor not labeled or wired correctly After replacing the tray motor with a new one the playerwould not work correctly, the tray would rotate back and forth and notrecognize the cd in the unit.
SONY XRU220
Key switches fail There seems to be a problem with the volume + switches withall xru, cdx5180 and cdxu8000 units. i have repaired ten units of variousmodel numbers over the past three months. some have been returns with thenewly replaced switch broken. is this a switch
SONY CDX51RF
Wired remote commander part numbers not in service manual The manual does not show any part numbers for the wiredremote commander supplied with the rf version. most of the parts areidentical to those found in the cdx-45rf manual, so the technicians orderparts from that manual. but in the case of the front pan
SONY CDX5180
Certain function buttons are inoperative (replace switches) Some of the function buttons do not work properly.
SONY GEN-CAM
Lanc jig hardware component value changes - d3, d4, r1 Two incorrect diodes were installed in the lanc jig. thisaffects 100 units and should be checked and corrected if necessary.
SONY GEN-CAM
Lanc jig software update version 2.1b now available An update to the lanc jig software is now available. the newversion is 2.1b.