Sony Repair Tips
Search: sony
Results: 20089
Results: 20089
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| SONY |
CFD600
|
Disk base missing stopper | Stopper is missing in new disk base. see attached copy.this can accidently cause the disk base to lock up. | ||
| SONY |
CFD600
|
Disc drawer doesn't close smoothly | After replacement of disc base, drawer, found new part hitssomething as it closes which causes drawer to move upward and overobstruction. since old drawer did not have this problem there must bea difference between old and new one. | ||
| SONY |
CFD600
|
Mechanism jams | Cd mechanism jams. several reports have been submittedregarding this problem. | ||
| SONY |
CFD600
|
Cd changer mech jammed | Received unit with cd jammed in changer. removed cd's.physically turned gear ref 267 so elevator gear brought the case (ref269) all the way in the up position. powered unit, the eliminator mechwent down and jammed. | ||
| SONY |
CFD600
|
When play is pressed, unit indicates take out disc | When all the discs are loaded and play is pressed, unitindicates: take out disc on every disc you attempt to play, 4th unit withthis problem. | ||
| SONY |
CFD600
|
Chucking problem | Disk chucks out of alignment sometimes. this causes thedisk to rub on mechanical assembly. | ||
| SONY |
CFD600
|
Can't mount sled motor on new turntable assy | New spindle motor comes attached to the turntable assy. whenattaching old parts to new turntable assy the holes for the sled motordon't line up. with some dificulty the new spindle motor can be removedand put on old turntable assy. -hq comments: conta | ||
| SONY |
CFD600
|
Wrong spindle motor | Spindle motor does not line up on cd motor board ref 251.spindle motor was ordered twice with same results. -hq comments: contact kansas city parts, attn jamie lyon phone #816-891-7550 ext 256, fax # 816-891-2580. | ||
| SONY |
CFD600
|
Replacement turntable assembly does not line up | The replacment turntable assemblies do not permit the cdmotor board to line up correctly with the spindle motor, and the sledmotor does not line up with the drilled holes. please advise. -hq comments: contact kansas city parts, attn jamie lyon phone # | ||
| SONY |
SVT5000
|
Very poor picture quality | Found rf level very low, causing poor picture quality especially on exit side. 3rd unit with problem in 1 month. | ||
| SONY |
SLVR5UC
|
Tape indicator wrong/ high speed rewind won't stop smoothly | 1. the unit may display the wrong tape indicator (tape may be full, while the incator may show mid range...) 2. high speed rewind won't slow down as the tape approaches the end and it will not stop smoothly. | ||
| SONY |
SLV940HF
|
Won't accept tape - relaced fl assy loading gear slide assy | Won't accept tape. | ||
| SONY |
SLV780HF
|
Play goes to shut down - replaced loading gear | Play goes to shut down. | ||
| SONY |
SLV780HF
|
Pb pix jumping - tape path alignment | Pix jumping in playback. | ||
| SONY |
SLV780HF
|
Tape gets stuck - replaced & realigned jammed cassette assy | Tape gets stuck. | ||
| SONY |
SLV780HF
|
Makes crackling noise when loading tape | Makes cracking sound when inserting tape. | ||
| SONY |
SLV780HF
|
Won't auto load, pix jumping on pb - tape path | No auto loading, pic jumping on pb. | ||
| SONY |
SLV780HF
|
Won't load tape - replaced parts in fl assy | Tape won't load. | ||
| SONY |
SLV780HF
|
Won't tune channels - poor connection on ic302 pin 33/34 | Will not tune channels | ||
| SONY |
SLV740HF
|
Int. on/off function - resold pins @ cn301/hi5 board | Intermittent on/off function. cold solder connections in all the odd pin numbers of the cn301, hi5 board. |