Sony Repair Tips
Search: sony
Results: 20089
Results: 20089
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| SONY |
CDPCA8ES
|
Whistling noise - add rtv btwn spindle motor & bd board | A whistling noise (about 400hz) manifests itself on certaincuts of disc (goodbye yellow brick road, elton john, polydor d103076). ifyou touch the optical block lightly, the noise disappears. | ||
| SONY |
CDPCA7ES
|
Whistling noise - add rtv btwn spindle motor & bd board | A whistling noise (about 400hz) manifests itself on certaincuts of disc (goodbye yellow brick road, elton john, polydor d103076). ifyou touch the optical block lightly, the noise disappears. | ||
| SONY |
CDPC745
|
Whistling noise - add rtv btwn spindle motor & bd board | A whistling noise (about 400hz) manifests itself on certaincuts of disc (goodbye yellow brick road, elton john, polydor d103076). ifyou touch the optical block lightly, the noise disappears. | ||
| SONY |
CDPC545
|
Whistling noise - add rtv btwn spindle motor & bd board | A whistling noise (about 400hz) manifests itself on certaincuts of disc (goodbye yellow brick road, elton john, polydor d103076). ifyou touch the optical block lightly, the noise disappears. | ||
| SONY |
CDPC445
|
Whistling noise - add rtv btwn spindle motor & bd board | A whistling noise (about 400hz) manifests itself on certaincuts of disc (goodbye yellow brick road, elton john, polydor d103076). ifyou touch the optical block lightly, the noise disappears. | ||
| SONY |
CDPC365
|
Door won't open - check if screws ref # 3 installed | These are dealer stock units and the door won't open. found that the bu holder ref # 110 fell off from the chassis. the screws ref # 3 were not installed at the factory. | ||
| SONY |
CDPC365
|
Whistling noise - add rtv btwn spindle motor & bd board | A whistling noise (about 400hz) manifests itself on certaincuts of disc (goodbye yellow brick road, elton john, polydor d103076). ifyou touch the optical block lightly, the noise disappears. | ||
| SONY |
CDPC335
|
Whistling noise - add rtv btwn spindle motor & bd board | A whistling noise (about 400hz) manifests itself on certaincuts of disc (goodbye yellow brick road, elton john, polydor d103076). ifyou touch the optical block lightly, the noise disappears. | ||
| SONY |
CDPC265
|
Whistling noise - add rtv btwn spindle motor & bd board | A whistling noise (about 400hz) manifests itself on certaincuts of disc (goodbye yellow brick road, elton john, polydor d103076). ifyou touch the optical block lightly, the noise disappears. | ||
| SONY |
CDPC235
|
Whistling noise - add rtv btwn spindle motor & bd board | A whistling noise (about 400hz) manifests itself on certaincuts of disc (goodbye yellow brick road, elton john, polydor d103076). ifyou touch the optical block lightly, the noise disappears. | ||
| SONY |
XRU800
|
Unit stays on when faceplate is removed (found c510 shorted) | Unit will stay on when you take out the faceplate. foundthat c510, part number 1-164-222-11, was shorted. | ||
| SONY |
XRC720
|
Unit illuminates, has no other functions (found d573 bad) | Unilink dead/unit dead. would light up but not do anything.anything. found d573 shorted. | ||
| SONY |
XR430
|
No power (found d579 defective) | No power but unit beeps when buttons are pressed. | ||
| SONY |
XR3200
|
Service manual correction: head azimuth adjustment screws | Supplement-1 showing screws for the azimuth adj. is wrong.specifically, the drawing in the supplement would lead you to believe thatthe 2 screws towards the front of the unit are for adjusting azimuth inthe forward direction, and the 2 screws towards the | ||
| SONY |
XR3050
|
Harness socket broken; part is "not supplied" | Cust dropped unit damaging cord receptacle. no other damageto unit. part listed as not supplied on page 28 (next to ref 62). | ||
| SONY |
EXR18
|
Service manual correction: head azimuth adjustment screws | Supplement-1 showing screws for the azimuth adj. is wrong.specifically, the drawing in the supplement would lead you to believe thatthe 2 screws towards the front of the unit are for adjusting azimuth inthe forward direction, and the 2 screws towards the | ||
| SONY |
CDXC590
|
Optical pickup/servo board incompatibility (kss-410a/313a) | The unit came in for service with type kss-313a opticalpickup, which was defective. the type shown in the service manual iskss-410a, which was ordered from npc and installed in the unit, but thispickup did not work in the customer's unit. | ||
| SONY |
CDXC490
|
Optical pickup/servo board incompatibility (kss-410a/313a) | The unit came in for service with type kss-313a opticalpickup, which was defective. the type shown in the service manual iskss-410a, which was ordered from npc and installed in the unit, but thispickup did not work in the customer's unit. | ||
| SONY |
CDX91
|
No analog audio when connected to xdp-u50d or mdx-u1 | When connected to the xdp-u50d or mdx-u1, there is no audio cdaudio if the analog connection is used (digital connection is ok). inreality, the audio is present on the cdx-91 analog output but the xdp-50dor mdx-u1 is not selecting it. problem occurs ev | ||
| SONY |
CDX600DSP
|
Optical pickup/servo board incompatibility (kss-313a/410a) | The unit came in for service with type kss-410a opticalpickup, which was defective. the type shown in the service manual iskss-313a, which was ordered from npc and installed in the unit, but thispickup did not work in the customer's unit. is there a pa |