Sony Repair Tips
Search: sony
Results: 20073
Results: 20073
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| SONY |
HCDH605
|
Wrong part | Ordered part 159057811 ref 267 which goes from bd board to cd board. part received was too long and too wide even though original was 19pin. | ||
| SONY |
HCDH405
|
Cd section jammed due to bent levers | The cd section may be jammed due to bent levers. | ||
| SONY |
HCDD260
|
No display - replaced d1323 on main bd (power supply section | No display. | ||
| SONY |
CDPCA9ES
|
Whistling noise - add rtv btwn spindle motor & bd board | A whistling noise (about 400hz) manifests itself on certaincuts of disc (goodbye yellow brick road, elton john, polydor d103076). ifyou touch the optical block lightly, the noise disappears. | ||
| SONY |
CDPCA8ES
|
Whistling noise - add rtv btwn spindle motor & bd board | A whistling noise (about 400hz) manifests itself on certaincuts of disc (goodbye yellow brick road, elton john, polydor d103076). ifyou touch the optical block lightly, the noise disappears. | ||
| SONY |
CDPCA7ES
|
Whistling noise - add rtv btwn spindle motor & bd board | A whistling noise (about 400hz) manifests itself on certaincuts of disc (goodbye yellow brick road, elton john, polydor d103076). ifyou touch the optical block lightly, the noise disappears. | ||
| SONY |
CDPC745
|
Whistling noise - add rtv btwn spindle motor & bd board | A whistling noise (about 400hz) manifests itself on certaincuts of disc (goodbye yellow brick road, elton john, polydor d103076). ifyou touch the optical block lightly, the noise disappears. | ||
| SONY |
CDPC545
|
Whistling noise - add rtv btwn spindle motor & bd board | A whistling noise (about 400hz) manifests itself on certaincuts of disc (goodbye yellow brick road, elton john, polydor d103076). ifyou touch the optical block lightly, the noise disappears. | ||
| SONY |
CDPC445
|
Whistling noise - add rtv btwn spindle motor & bd board | A whistling noise (about 400hz) manifests itself on certaincuts of disc (goodbye yellow brick road, elton john, polydor d103076). ifyou touch the optical block lightly, the noise disappears. | ||
| SONY |
CDPC365
|
Door won't open - check if screws ref # 3 installed | These are dealer stock units and the door won't open. found that the bu holder ref # 110 fell off from the chassis. the screws ref # 3 were not installed at the factory. | ||
| SONY |
CDPC365
|
Whistling noise - add rtv btwn spindle motor & bd board | A whistling noise (about 400hz) manifests itself on certaincuts of disc (goodbye yellow brick road, elton john, polydor d103076). ifyou touch the optical block lightly, the noise disappears. | ||
| SONY |
CDPC335
|
Whistling noise - add rtv btwn spindle motor & bd board | A whistling noise (about 400hz) manifests itself on certaincuts of disc (goodbye yellow brick road, elton john, polydor d103076). ifyou touch the optical block lightly, the noise disappears. | ||
| SONY |
CDPC265
|
Whistling noise - add rtv btwn spindle motor & bd board | A whistling noise (about 400hz) manifests itself on certaincuts of disc (goodbye yellow brick road, elton john, polydor d103076). ifyou touch the optical block lightly, the noise disappears. | ||
| SONY |
CDPC235
|
Whistling noise - add rtv btwn spindle motor & bd board | A whistling noise (about 400hz) manifests itself on certaincuts of disc (goodbye yellow brick road, elton john, polydor d103076). ifyou touch the optical block lightly, the noise disappears. | ||
| SONY |
XRU800
|
Unit stays on when faceplate is removed (found c510 shorted) | Unit will stay on when you take out the faceplate. foundthat c510, part number 1-164-222-11, was shorted. | ||
| SONY |
XRC720
|
Unit illuminates, has no other functions (found d573 bad) | Unilink dead/unit dead. would light up but not do anything.anything. found d573 shorted. | ||
| SONY |
XR430
|
No power (found d579 defective) | No power but unit beeps when buttons are pressed. | ||
| SONY |
XR3200
|
Service manual correction: head azimuth adjustment screws | Supplement-1 showing screws for the azimuth adj. is wrong.specifically, the drawing in the supplement would lead you to believe thatthe 2 screws towards the front of the unit are for adjusting azimuth inthe forward direction, and the 2 screws towards the | ||
| SONY |
XR3050
|
Harness socket broken; part is "not supplied" | Cust dropped unit damaging cord receptacle. no other damageto unit. part listed as not supplied on page 28 (next to ref 62). | ||
| SONY |
EXR18
|
Service manual correction: head azimuth adjustment screws | Supplement-1 showing screws for the azimuth adj. is wrong.specifically, the drawing in the supplement would lead you to believe thatthe 2 screws towards the front of the unit are for adjusting azimuth inthe forward direction, and the 2 screws towards the |