Sony Repair Tips
Search: sony
Results: 20100
Results: 20100
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| SONY |
CDXU303RF
|
Part # correction: q503 (correct part # is 8-729-204-10) | Found part # for q503 8-729-240-10, was not in system (fipm).looked in semi-conductor replacement handbook and found that the # for2sd1417 is actually 8-729-204-10 (page 700 of 1992 2nd srm). we had thepart in stock and the unit was repaired. | ||
| SONY |
CDX7580
|
Does not play discs (fok signal voltage only reaches 1.5v) | The fok line would only rise to ~ 1.5v. problem was caused byic2 (servo ic) loading it down. | ||
| SONY |
CDX7560
|
Pll adjustment drifts (found c24 & c25 leaking electrolyte) | Unit would play fine for a few days after pll was adjusted.found c24 and c25 electrolytic capacitors leaking oil to the board.schematic location i, j-10. | ||
| SONY |
CDX7560
|
Does not play discs (fok signal voltage only reaches 1.5v) | The fok line would only rise to ~ 1.5v. problem was caused byic2 (servo ic) loading it down. | ||
| SONY |
CDX7540
|
Does not play discs (fok signal voltage only reaches 1.5v) | The fok line would only rise to ~ 1.5v. problem was caused byic2 (servo ic) loading it down. | ||
| SONY |
CDX7520
|
Does not play discs (fok signal voltage only reaches 1.5v) | The fok line would only rise to ~ 1.5v. problem was caused byic2 (servo ic) loading it down. | ||
| SONY |
CDX65RF
|
Does not load cd's; makes noise (found ref. 221 damaged) | Customer complaint: constantly will not play. open unit tocheck, found does not take any cd into roller. #164 slide lever and 221gear made noise when trying load discs. | ||
| SONY |
CDX65RF
|
Part # correction: q503 (correct part # is 8-729-204-10) | Found part # for q503 8-729-240-10, was not in system (fipm).looked in semi-conductor replacement handbook and found that the # for2sd1417 is actually 8-729-204-10 (page 700 of 1992 2nd srm). we had thepart in stock and the unit was repaired. | ||
| SONY |
CDX65
|
Does not load cd's; makes noise (found ref. 221 damaged) | Customer complaint: constantly will not play. open unit tocheck, found does not take any cd into roller. #164 slide lever and 221gear made noise when trying load discs. | ||
| SONY |
CDX5080
|
Does not play discs (fok signal voltage only reaches 1.5v) | The fok line would only rise to ~ 1.5v. problem was caused byic2 (servo ic) loading it down. | ||
| SONY |
CDX5040
|
Does not play discs (fok signal voltage only reaches 1.5v) | The fok line would only rise to ~ 1.5v. problem was caused byic2 (servo ic) loading it down. | ||
| SONY |
CDX45RF
|
Part # correction: q503 (correct part # is 8-729-204-10) | Found part # for q503 8-729-240-10, was not in system (fipm).looked in semi-conductor replacement handbook and found that the # for2sd1417 is actually 8-729-204-10 (page 700 of 1992 2nd srm). we had thepart in stock and the unit was repaired. | ||
| SONY |
CDX45
|
Intermittent loading problems (found ph11 defective) | First unit intermittently would not find correct disc then gotstuck in that position. heard mech noise elevator and worm gear ref 205,m501, were both torn up a bit. replaced these parts then unit would go upto disc 5 at most, found ph1 was almost short | ||
| SONY |
CDX4040
|
Does not play discs (fok signal voltage only reaches 1.5v) | The fok line would only rise to ~ 1.5v. problem was caused byic2 (servo ic) loading it down. | ||
| SONY |
CCDV8AFU
|
Ic501 getting hot drum speed erratic/replace q508 | During playback or camera rec drum does not get on speed.ic501 gets hot and unit shuts down. flashing eject led appears. | ||
| SONY |
CCDV8
|
Green picture from camera/replace ic 705 | No video coming from camera section, green screen. problemwas caused by 2 v line from ic 705 dropping below 1v. replaced ic705resolved problem. the 2 v line is used as areference voltage for manyadjustments. must be right on for proper operation. | ||
| SONY |
CCDTR81
|
Part number for cassette basket assy | What is the part number for the cassette compartment in thismodel? | ||
| SONY |
CCDTR80
|
Tape will not load/re-seat cn500 | Drum runs fast. | ||
| SONY |
CCDTR700
|
Missing segments in lcd/replace ic902 | Missing segments in lcd display. cuased by ic902/ p. 59 modecontrol cpu being continually low. pin 59 is part of segment drivecircuit. replacement of ic902 resolved problem. | ||
| SONY |
CCDTR5
|
No mic audio/replace c413 | Subbed mic pcb to see if it was the problem. mic pcbdefinitely had a probllme follwoing power to q405, r415 which had 4.7v onobth sides. there was an open between r415 and base of q405. c413 wasleaky which caused this trace to open up. |