Sony Repair Tips
Search: sony
Results: 20075
Results: 20075
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| SONY |
MDS101
|
Unit stuck in standby mode - re-position jammed eject switch | Unit stuck in standby. eject button constantly depressed. | ||
| SONY |
MDS101
|
Would not eject disc - repl missing washer, ref.# 52 | Unit would not eject disc. washer on top left cover of sliderassy missing, which misaligned mech and made disc sit incorrectly. | ||
| SONY |
HCDH150
|
No power - replaced +5v regulator and zener d735 | No power. | ||
| SONY |
HCDC50U
|
Cd loading too fast - replaced ic414 | Travels to fast causing cd's to shift out of tray. | ||
| SONY |
HCDC33
|
Unit flashes initializing - cd section needs alignment | When power plug is pulled out and plugged back in unit flashesinitializing on display until cd mech cycles through all drawers. if cddoes not cycle due to a jam, the unit will not come out of theinitializing cycle. unit will turn on but when it is powe | ||
| SONY |
HCDC33
|
Cd jammed - realigned mechanism | Mechanism jammed. trays 333-337 slide into main tray, 310, inthis case tray 337 did not latch into 310 causing the mech to jam. | ||
| SONY |
DTC700
|
New slant block assy left/right not working | Upon installation of the new slant block assy, left/right,they are not sliding freely in the slot on the chassis. when screw 628 istightened in place with ref 606, plate assy, loading, the two pieces arepinched together. | ||
| SONY |
DTC59ES
|
Eats tapes - tightened capstan mount screws | Unit eats tape at beginning of 120 min. tape in long mode.found tape would ride down on capstan. | ||
| SONY |
CDPC615
|
No tray rotation or bu assm chucking - repl flex cable | Tray would never rotate. bu assm would never chuck. | ||
| SONY |
CDPC335
|
Tray motor spinning backwards - replace table motor | Ran into this problem 5 times in past 3 weeks. removed traymotor. old motor is installed with lable on motor facing up. if newmotor is installed with lable facing up, motor will spin backwards andtray will not function properly. | ||
| SONY |
CDP590
|
Incorrect part # j401 - correct part #156692111 | The microfiche service infomration gives j401 as part #1-569-442-11. this is incorrect. | ||
| SONY |
XRU880
|
Dead unit (replaced q504 and d513) | Unit was dead. master control ic was on but would not powerup unit (pin 5 stayed low). bus on pin 38 would pulse low 3 times whenunit was powered up. data and clock lines would show initial activity. | ||
| SONY |
XRU770
|
Dead unit (replaced q504 and d513) | Unit was dead. master control ic was on but would not powerup unit (pin 5 stayed low). bus on pin 38 would pulse low 3 times whenunit was powered up. data and clock lines would show initial activity. | ||
| SONY |
XRC410
|
Mechanism gear alignment procedures available in supp. #1 | The mechanism in this model uses gears and encoders which mustbe aligned properly in order for the mechanism to work, but the manualdoes not detail the alignment procedure. | ||
| SONY |
XRC210
|
Mechanism gear alignment procedures available in supp. #1 | The mechanism in this model uses gears and encoders which mustbe aligned properly in order for the mechanism to work, but the manualdoes not detail the alignment procedure. | ||
| SONY |
CDX5470
|
Optical pickup received from npc does not work in unit | The unit came in for service with type kss-410a opticalpickup, which was defective. the type shown in the service manual iskss-313a, which was ordered from npc and installed in the unit, but thispickup did not work in the customer's unit. is there a pa | ||
| SONY |
CDX5270
|
Optical pickup received from npc does not work in unit | The unit came in for service with type kss-410a opticalpickup, which was defective. the type shown in the service manual iskss-313a, which was ordered from npc and installed in the unit, but thispickup did not work in the customer's unit. is there a pa | ||
| SONY |
CDX5070
|
Optical pickup received from npc does not work in unit | The unit came in for service with type kss-410a opticalpickup, which was defective. the type shown in the service manual iskss-313a, which was ordered from npc and installed in the unit, but thispickup did not work in the customer's unit. is there a pa | ||
| SONY |
CDX45
|
Discs don't spin, "e04" shown on display (replaced ic13,q21) | Loads the cd but will not spin, shows e04 on display. | ||
| SONY |
CDV701
|
Most function buttons do not operate/check eject button | Most of the function switches do not operate. a selected fewwill respond. unit resembled having a button stuck in the activated mode. i was not able to track this down by checking key scan lines to and fromthe micro. i was able to determine the fault |