☰

Sony Repair Tips




AIWA
BEKO
CCE
CINERAL
DAEWOO
FUNAI
GRADIENTE
GRUNDIG
HITACHI
ITT
JVC
LG
MITSUBISHI
PANASONIC
PHILCO
PHILIPS
PIONEER
RCA
SAMSUNG
SANYO
SHARP
SONY
THOMSON
TOSHIBA
VESTEL


Search: sony
Results: 20100
Make Model Symptom Problem Solution By
SONY CDX5470
Optical pickup received from npc does not work in unit The unit came in for service with type kss-410a opticalpickup, which was defective. the type shown in the service manual iskss-313a, which was ordered from npc and installed in the unit, but thispickup did not work in the customer's unit. is there a pa
SONY CDX5270
Optical pickup received from npc does not work in unit The unit came in for service with type kss-410a opticalpickup, which was defective. the type shown in the service manual iskss-313a, which was ordered from npc and installed in the unit, but thispickup did not work in the customer's unit. is there a pa
SONY CDX5070
Optical pickup received from npc does not work in unit The unit came in for service with type kss-410a opticalpickup, which was defective. the type shown in the service manual iskss-313a, which was ordered from npc and installed in the unit, but thispickup did not work in the customer's unit. is there a pa
SONY CDX45
Discs don't spin, "e04" shown on display (replaced ic13,q21) Loads the cd but will not spin, shows e04 on display.
SONY CDV701
Most function buttons do not operate/check eject button Most of the function switches do not operate. a selected fewwill respond. unit resembled having a button stuck in the activated mode. i was not able to track this down by checking key scan lines to and fromthe micro. i was able to determine the fault
SONY CCDTR82
No steady shot No steady shot indicator showed in viewfinder.
SONY CCDTR77
No camera output/resolder l710 The camera had no output. the problem was caused by l710 onthe vc136 board being poorly soldered on one side. re-soldering resolvedthe problem.l 710 is in the camera 5v line. when it opens the camera sections isbasically dead.
SONY CCDTR71
Only zooms one way/replace ic855 Unit would only zoom in the direction that zoom was firsttried at power-on. if you tried wide first, it would only zoom wide untilyou turned power off. after killing power if you tried tele first, wouldonly zoom in the telephoto.
SONY CCDTR71
Broken view finder latch View finder latch breaks off and you must replace (or at leastorder) the entire right cabnet to fix it. can the latch be made aseperate part number? -hq comments: we investigated this before, and found it to be tooexpensive to get a sufficient quantity
SONY CCDTR70
New vc-145 does not work change page f add 00 to data 5e New vc-145 does not work
SONY CCDTR7
Loses y signal after a few minutes/replace c318 Would lose y signal after unit was on for a few minutes.
SONY CCDTR400
Noisy capstan, intermittent rotation/replace capstan motor Noisy capstan, intermittent rotation.
SONY CCDFX620
Part number for tele/wide switch incorrect/1-692-257-21 Drawing in s/m is incorrect showing plug in flex connector andswitch board. flex board is actually part of switch assy.
SONY CCDFX530
Drum problem/resolder ic505 Drum assy runs extremely fast.
SONY CCDFX530
No focus, no zoom/replace lens block No focus, no zoom
SONY CCDFX510
Premature tape end detection We need clarification on csv-3 service bulletin #333. the partlisted as c865 is a filter cap on the focus motor b+ line on p.116. thedrawing in the s/b shows c559, which is a filter on 5v regulator ic508 onp.122. which cap should be changed for this symp
SONY CCDF55
Japanese characters for month on osd, lcd display ok Due to water damage, we had to replace the ct21 board on thisunit. after installation, we could not get the osd to display the datecorrectly. either it was yy/mm/dd or mm/dd/yy, but with the month injapanese characters.
SONY GDM17SE1
Screen slowly disappears check c625 on the g-board The symptom of screen slowly diappearing was caused by c625failure. -hq comments: thank you. please see bulletin 70.
SONY CPD15SF1
Misconvergenge caused by a board shield case (degauss case)
SONY CPD15SF1
Intermittent focus problem, degaus crt neck with unit on Focus changes intermittently. -hq comments: degauss a crt around the neck area while the unit is in the on position. this may remove the problem. if this fails to work,replace the picture tube.