Sony Repair Tips
Search: sony
Results: 20092
Results: 20092
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| SONY |
KV32TS46
|
Unable to change channels in pip, reset id code 52/53 | Using remote control and pressing p-p for display, unit ok.tried changing channels and could not change channels. | ||
| SONY |
KV32TS46
|
Dead, no standby 5v, replace ic602 reset ic | Unit won't turn on, no standby 5v to ic101. unsoldering thereset line, pin 4 of ic602, the unit powers up. | ||
| SONY |
KV32TS35
|
Retrace line on blue screen, unit shuts off, leaky q702 | Blue screen and retrace lines when first turned on then setshuts off. | ||
| SONY |
KV32SXR10
|
Intermittent loss of video, resoldered delay line | Int loss of video or negative video. | ||
| SONY |
KV27XBR60
|
Part number for diode d-251 (x1 board) 8-719-110-48 | Need the part number for diode on the x board located atic251/pin 11. -hq comments: discription part number rd18esb1 8-719-110-48 | ||
| SONY |
KV27XBR60
|
Horizontal line in center of screen, replaced diode x board | If g2 was turned up, a white horizontal line appeared acrossthe center of the screen. unit would not accept any commands. symptomappeared to suggest a data problem. data lines were loaded down comingfrom the surround board (x board). the data lines a | ||
| SONY |
KV27XBR10
|
No pix, has hv & sound, replaced diode d514 | No pix - had sound & hv, ic031 was blanking due to d514shorting pulling base of q506 low, pulling its emitter low, pulling pin27 of ic301 low, thus blanking the picture. | ||
| SONY |
KV27V55
|
Poor b+ regulation, replaced power module ic601 | H-width was small and vertical size was too large. b+ waslow. freezing ic601 brought pix back to normal. | ||
| SONY |
KV27V55
|
Spanish menu on screen, setup change from service mode | Bringing up the menu it's all in spanish. unable to selectenglish. changing the id codes for the kv27v55 did not help. | ||
| SONY |
KV27V15
|
Noise bars in pix with cable hooked up, dg shorted to metal | When cable was hooked up to the set there would be bars inthe picture and audio hum from the speakers. by removing the dg coilconnector (cn113) the noise would go away. removing thermistor orrelay did not affect the noise. | ||
| SONY |
KV27V15
|
No information on cable mouse in service manual, use i/m | The service manual for this set does not explain how tohook-up or use the cable mouse with the set. | ||
| SONY |
KV27V10
|
Remote not compatible with gi cable box or panasonic vcr | Customer has a 1994 panasonic vcr model pv4451, and a generalinstrument cable box model cft-2000, that will not operate using thermy-117 remote. they tried codes 70, 71, and 72. -hq comments: since these are 1994 models the codes they used mustbe new | ||
| SONY |
KV27TX20
|
Dead, replaced d601 and fuse f601 | Dead lightning. | ||
| SONY |
KV27TX20
|
Snowy picture, replaced q599 and d599 | Lightning snowy picture. | ||
| SONY |
KV27TX20
|
Snowy picture, replaced q009 and q008 | Lightning. antenna will not switch from ant to aux.picture is slightly snow on some channels. | ||
| SONY |
KV27TS36
|
Ic610 p/n incorrect, 8-759-708-05 | Part number in s/m for ic610 is incorrect. please help -hq comments: the correct part number is 8-759-708-05 njm78l05a | ||
| SONY |
KV27TS32
|
Ic610 p/n incorrect, 8-759-708-05 | Part number in s/m for ic610 is incorrect. please help -hq comments: the correct part number is 8-759-708-05 njm78l05a | ||
| SONY |
KV27TS31
|
No pix, has sound & h.v., resoldered r701 on "c" board | Has sound and hv but no raster. 1000v present at c board butnot at g2 pin on crt. | ||
| SONY |
KV27TS29
|
Unit will not stop on active channel continues scanning | Unit would not stop on active channels, would continuescanning. flexing, cooling the m board would allow it to functionnormally for a time. | ||
| SONY |
KV27TS29
|
Ic610 p/n incorrect, 8-759-708-05 | Part number in s/m for ic610 is incorrect. please help -hq comments: the correct part number is 8-759-708-05 njm78l05a |