Sony Repair Tips
Search: sony
Results: 20102
Results: 20102
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| SONY |
KV27V15
|
No information on cable mouse in service manual, use i/m | The service manual for this set does not explain how tohook-up or use the cable mouse with the set. | ||
| SONY |
KV27V10
|
Remote not compatible with gi cable box or panasonic vcr | Customer has a 1994 panasonic vcr model pv4451, and a generalinstrument cable box model cft-2000, that will not operate using thermy-117 remote. they tried codes 70, 71, and 72. -hq comments: since these are 1994 models the codes they used mustbe new | ||
| SONY |
KV27TX20
|
Dead, replaced d601 and fuse f601 | Dead lightning. | ||
| SONY |
KV27TX20
|
Snowy picture, replaced q599 and d599 | Lightning snowy picture. | ||
| SONY |
KV27TX20
|
Snowy picture, replaced q009 and q008 | Lightning. antenna will not switch from ant to aux.picture is slightly snow on some channels. | ||
| SONY |
KV27TS36
|
Ic610 p/n incorrect, 8-759-708-05 | Part number in s/m for ic610 is incorrect. please help -hq comments: the correct part number is 8-759-708-05 njm78l05a | ||
| SONY |
KV27TS32
|
Ic610 p/n incorrect, 8-759-708-05 | Part number in s/m for ic610 is incorrect. please help -hq comments: the correct part number is 8-759-708-05 njm78l05a | ||
| SONY |
KV27TS31
|
No pix, has sound & h.v., resoldered r701 on "c" board | Has sound and hv but no raster. 1000v present at c board butnot at g2 pin on crt. | ||
| SONY |
KV27TS29
|
Unit will not stop on active channel continues scanning | Unit would not stop on active channels, would continuescanning. flexing, cooling the m board would allow it to functionnormally for a time. | ||
| SONY |
KV27TS29
|
Ic610 p/n incorrect, 8-759-708-05 | Part number in s/m for ic610 is incorrect. please help -hq comments: the correct part number is 8-759-708-05 njm78l05a | ||
| SONY |
KV27TS29
|
Intermittent noise in picture, c636 was touching fb603 | C636 was bent over touching fb603. intermittently the picturehad bars and other interference in it. | ||
| SONY |
KV27TS27
|
No power, replaced ic607 & q614 on d board | No power on. checked the following: q601/602, r647 - okstandby voltage - ok ic101-56, pwr on/off - ok ic101-20, relay drive, -ok q604, relay driver, - ok ic607-1&2 - no change in voltage pin 1 & 2open. | ||
| SONY |
KV27TS20
|
No chroma, replaced leaky c508 off jungle ic301 pin 12 | No color. checked following: comb filter, pin 4 ok ic301-46ok changed x301, no help ic301-12, waveform ok, but dc voltage at 0.5instead of 3.2vdc c508 - 300Ω leakage. | ||
| SONY |
KV27HSR10
|
Srs module does not fit on pcb | Part 874159202 (original with metal spikes you solder in thepcb) substitutes to 874159101 (plastic strip for a female connection).874159101 cannot fit on the pcb. -hq comments: substitution of this part was wrong. kcp will correct. iwill keep you updat | ||
| SONY |
KV2790R
|
Intermittent pic snow & audio distorts, resoldered if area | Int. picture goes to snow, audio distorts. | ||
| SONY |
KV2780R
|
Snowy pic on all high channels, replaced q1411/1412 ant sw | Snowy picture all higher channels. | ||
| SONY |
KV25XBR
|
Dead , replaced "c" board and flyback | Found unit dead bad fbt taking out 40v line to c board.replaced c board and the new one started to burn pack on d board.found leads of connector d6 switched on 2 new boards, the 200v and 40vwire. | ||
| SONY |
KV25XBR
|
Dead, replaced fbt, h out and hvr | Found shorted fbt, h out and cracked hvr. | ||
| SONY |
KV25XBR
|
No video/audio, sleep on, replaced flyback transformer | Sleep comes on but no video or audio. | ||
| SONY |
KV2152M9
|
Dead, replaced d613 & ic602 | Unit dead no b+. ic 602 is hot. found d613 shorted. |