Sony Repair Tips
Search: sony
Results: 20077
Results: 20077
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| SONY |
SRFHM55
|
Battery door pops open when batteries are inserted | Battery door pops open when batteries are inserted. there isa tab inside the battery cabinet that is easily worn down. it is locatedby battery lid hinge. also applies to serial numbers 20088 and 25484. | ||
| SONY |
MZR2
|
No audio from line out jack - replaced main board | Intermittent audio from line out jack left channel only.found extremely thin, very difficult to see, crack along line out jack.also found several intermittent solder connects and feed thrus whiletracing audio back thru main board from q102, 202 to ic311, | ||
| SONY |
MZR2
|
Intermittent power from adaptor - resoldered cn801 | Intermittent power to unit when using ac adaptor, found flexboard that runs from d-d converter to cn801 on main board had brokenconnections on d-d conv. side. | ||
| SONY |
MZ1
|
Popping in audio rec from digital in only | Popping in audio, but only from digital power supply, analog recok. | ||
| SONY |
M2000
|
Tape speed varies | Pinch roller will not contact capstan. tape speed varies.the shaft that connects with spring 59 is bent or part of the pinch rollerassy is bent. | ||
| SONY |
DT66
|
No audio onto headphones - replace r306, p/n 1-216-835-11 | No audio from headphones jack, line out is ok. missing b+ toic303 headphone amp. found r306 15k resistor off q302 to be open,measured approx 1.3 mg. | ||
| SONY |
DT10
|
No sled or spindle - install jumper from ic401/pin 10 & r401 | No sled or spindle. missing 4.7v output at q401. this lineprovides b+ to ic502, ic504 and various other points. found an openbetween r401 and pin 10 of ic401. pin 10 was missing the required 4.6v. | ||
| SONY |
D421SP
|
Part number not supplied | Manual problem, hinge part # not supplied. -hq comments: hinge is not supplied separately. please order p/nx-494-391-21. | ||
| SONY |
D121
|
Main board in unit isn't the same layout as s/m | Main board in the unit isn't the same as the one in the s/m.p/n on the board in unit is 164724113. very difficult to troubleshootsince the layout is different. is there a supplement for the new boardlayout. -hq comments: yes there is supplement-1, p/ | ||
| SONY |
CFSW470
|
Replacement pwr xfmr leads differ from orig | Leads of replacement transformer are slightly different fromoriginal part so transformer and board do not fit properly into cabinet.nothing on sdis for this model. -hq comments: kcp received a new shipment from wrpc. please reorder andif the part does n | ||
| SONY |
CFD758
|
Kss360a has wrong connector | The kss360a, 884824601, which subs to 884824611, has a flexconnector that is approx. 1 wide. the assembly coming out of unit beingrepaired uses a connector that is 3/4 wide. | ||
| SONY |
CFD758
|
Sled motor noise | On later (outer) tracks, sled motor made a clicking noisewhen changing tracks. | ||
| SONY |
CFD755
|
Hum at low volume on right side - remove glue from r285 | Hum at low volume on the right side. -hq comments: clean conducting glue from r285. | ||
| SONY |
CFD755
|
No audio - replace ic703, p/n 8-752-337-26 | Static only (no audio) when playing cd. | ||
| SONY |
CFD703
|
Distorted audio - replace ic353 | Left speaker/channel distorted. | ||
| SONY |
CFD600
|
Jamming of cd discs | Cd discs which are loaded into the disc case, (item 269, page40), can become misaligned in the grooves due to normal transporting ofthe player. when a particular disc is selected for play, the disc casemoves vertically until the selected disc lines up wi | ||
| SONY |
CFD600
|
Would not read discs | Won't always play disc/next disc. disc mtor turned, but itwould not read disc. | ||
| SONY |
CFD560
|
No display windows with cabinet | No display windows with cabinet. need part numbers for displaywindows on front cabinet. -hq comments: tokyo has been advised. the next shipment from tokyo willhave the window included. use same part number. | ||
| SONY |
CFD460
|
Cassette door stays shut | Activating arm is warped, bent, deformed to the point where the door won't open. the new one is bent differently but equally effective. | ||
| SONY |
CFD30
|
Tape motor replacement | Ordered 3 new tape motors and all three turned backwards(counter clockwise). |