Sony Repair Tips
Search: sony
Results: 20077
Results: 20077
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| SONY |
CCDVX3
|
No camera power/cn-252, fu-107 board unplugged | There was no camera power, the title in viewfinder had nosync. | ||
| SONY |
CCDF77
|
No record/replace c-911 | There had been a complaint of no recording. the drum wasrunning at high speed. an open cap caused improper vs voltage to beapplied to drum motor. -hq comments: c-911 is connected between q-901 emitter (drum vs reg) andground. | ||
| SONY |
SL2700
|
Intermittent hum on left channel: resolder bpf811/812 af1 bd | Intermittent hum recorded in left audio channel. playback oftape recorded on another machine played fine. | ||
| SONY |
CCDFX710
|
F-950 open/replace f-950 | Customer complained of unit inoperative at turn on. i couldnot get a new fuse to blow. current measurements appeared normal. -hq comments: please refer to technical flash no. 88. please sendsamples and fill in the form attached to tf #88. | ||
| SONY |
CCDFX310
|
Crt part number unlisted/check ccd-fx620 manual page 185 | This unit had the vf51 ckt board as per evf type b noted inthe ccdfx620 service manual however, the crt type m01kta8wb part number isnot included in the service manual information as per fpr o0761. we foundpart number 145256511 listed for this crt type | ||
| SONY |
KV27TS32
|
Horizontal tear, reset the micro by unplugging | Billy woodfin, reported to me regarding a customer in utah,who turned on the television and found the picture to be in a horizontaltear. the customer was instructed to unplug the set and when he replugedthe set in, everything reset. i could not find ou | ||
| SONY |
XR5600
|
Intermittently will not turn on (re-solder cnp906 pin 1) | The unit intermittently will not power up. | ||
| SONY |
KV20EXR20
|
Immediate shutdown, replaced q604 (g board) | The set would shut down immediately at power on. | ||
| SONY |
KV27EXR20
|
Dark picture and/or blue snow, replaced q711 (c board) | On a weak signal or no signal conditions, the screen wouldeither turn blue or have blue or red snow. at times, the picture would bevery dark. i traced this problem to q711 ik detect buffer. emitter/basemeasured about 59Ω. | ||
| SONY |
SPPA40
|
No battery backup | The battery spring (a), ref 19 was missing from the unit.this is the second time in a week i have seen this problem. qc? -hq comments: it could be a qc or manufacturing error. please gatherserial numbers of subsequent units with this problem and then w | ||
| SONY |
SSM620AM
|
Main board part number change, see chart below | The part number for the main board starting at serial number101201 has been changed. this board is common to models ssm-610, -621am,and -6020se. solution: reference description part number serial number 11 main | ||
| SONY |
SSM620AM
|
Change in relay ry-801, part number, see below | There are two types of power relay used in this model. pleaseorder the relay using the part numbers below.reference description part number serial numberry-801 power relay 9-994-059-01 up to 101,200ry-801 power rela | ||
| SONY |
SSM621AM
|
Part number for relay incorrect, 9-995-671-01 | Part number for the power relay, reference ry-801, isincorrect. | ||
| SONY |
WMFX55
|
Unwanted switching of tape sides - resolder j-301. | There were assorted tape control problems such as switchingfrom side to side, etc. or seemingly remote control problems. i have seenthis problem on several units. | ||
| SONY |
CFD768
|
Intermittent audio (resolder cn316 on megabass board) | Audio was intermittent. | ||
| SONY |
CFD758
|
Intermittent audio (resolder cn316 on megabass board) | Audio was intermittent. | ||
| SONY |
CDPC505
|
Legs of power transformer do not match holes on pcb | The power transformers supplied by npc (p/n 1-449-954-11) havelegs which do not line up with the holes on the power pcb. -hq comments: tokyo has advised that the transformer can be adapted tothe power board by trimming the two leads that do not match th | ||
| SONY |
CDPC305
|
Legs of power transformer do not match holes on pcb | The power transformers supplied by npc (p/n 1-449-954-11) havelegs which do not line up with the holes on the power pcb. -hq comments: tokyo has advised that the transformer can be adapted tothe power board by trimming the two leads that do not match th | ||
| SONY |
CDPC205
|
Legs of power transformer do not match holes on pcb | The power transformers supplied by npc (p/n 1-449-954-11) havelegs which do not line up with the holes on the power pcb. -hq comments: tokyo has advised that the transformer can be adapted tothe power board by trimming the two leads that do not match th | ||
| SONY |
CDPC201
|
Legs of power transformer do not match holes on pcb | The power transformers supplied by npc (p/n 1-449-954-11) havelegs which do not line up with the holes on the power pcb. -hq comments: tokyo has advised that the transformer can be adapted tothe power board by trimming the two leads that do not match th |