Sony Repair Tips
Search: sony
Results: 20077
Results: 20077
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| SONY |
EVC50
|
Lanc jig | If control l switch is set to s position, this unit may be runon lanc jig to check for intermittents or to just verify operations. -hq comments: this is correct, any vcr with a control l input shouldfunction correctly. as you stated they must be in sla | ||
| SONY |
EVC40
|
Lanc jig | If control l switch is set to s position, this unit may be runon lanc jig to check for intermittents or to just verify operations. -hq comments: this is correct, any vcr with a control l input shouldfunction properly for a functional check. as you stat | ||
| SONY |
TCS430
|
Part number correction - ic-301 | Incorrect part number in the service manual. ic-301 is listedas 8-759-907-63. | ||
| SONY |
LANCJIG
|
No cue or rev operation with older models | Isreal reported that there is no cue or review operation witholder models ccd-f70 and ccd-f45 were examples. -hq comments: we will check into this as some of the lanc codes havebeen slightly changes over the years. | ||
| SONY |
KV27TS32
|
Unit out of horizontal sync, disconnected ac, and repluging | Customer in rural utah has a set out of horizontal sync. ihad the customer disconnect for about 10-15 seconds and plug back in. inareas with lightning and/or voltage surges the set can lock up.disconnecting and reconnecting resets the micros. -hq comm | ||
| SONY |
CCDV99
|
Distorted picture on playback | The unit produced no picture in playback or ee mode. thecamera continuously produced a gray screen only. i traced signal to pins1 of ic403 and ic404. the signal appeared at both inputs but would outputsync only at pin 7. q491 is used as a sync to det | ||
| SONY |
CCDTR5
|
No pb video, audio ok/c236 vs22 bd | There was no playback in video, but audio is good. | ||
| SONY |
SSCM256
|
Ic205 part number: 875205125 replaces 875205366 | Ic204 is listed in the manual as 875205366. this part is notavailable from kansas city. | ||
| SONY |
KV20TS32
|
Closed caption edges uneven, normal operation | Closed caption has uneven edges and video will move into blackbox by two to three lines. referred to yukio suto per kirk vistain andsent an 8mm tape to suto. -hq comments: after viewing the tape and speaking with jim it wasdetermined the caption circui | ||
| SONY |
AVU270
|
Unit inoperative - d901 faulty p/n 8-719-107-94 | After replacing the ac relay power switch xistors q813 anddriver q812, the new q813 is inoperative again after turning it on. ifound d901 was bad (spark killer diode on ry 901- ac relay). note: theschematic is incorrect at numerous places for instance- | ||
| SONY |
STRD990
|
Orientation on d301 and d302 shown incorrectly in s/m | The orientation on d301 and d302 in the schematic diagram(page 24, location p/8) and the pcb layout (page 28, location e/8) isshown incorrectly (both shown reversed). | ||
| SONY |
STRD790
|
Orientation on d301 and d302 shown incorrectly in s/m | The orientation on d301 and d302 in the schematic diagram(page 24, location p/8) and the pcb layout (page 28, location e/8) isshown incorrectly (both shown reversed). | ||
| SONY |
STRD2090
|
P/n for rm-p321 remote commander not listed, 1-693-098-11 | The part number for the remote commander rm-p321 is not shownin the service manual. | ||
| SONY |
STRGX99ES
|
Part number for rm-p321 remote commander | The part number for the remote commander rm-p321 is not shownin the service manual. | ||
| SONY |
KV1975R
|
Ic-301 no longer available, please refer to tvp sb # 25 | Service bulletin ctv-0236 states 875201920 is not areplacement for 8-752-008-20. the kansas city parts screen shows8-752-008-20 as out of stock and the replacement part is 8-752-019-20 ifthis is correct, how do you get it to work? if this is incorrect, | ||
| SONY |
XR5250
|
New tape deck chassis different from original | The pin used to mount lever number 202 had a groove for e-ringin a different position. the original chassis had a groove positioned forthe e-ring to mount directly on top of the lever. the new chassis has agroove higher up on the pin which allows the s | ||
| SONY |
KV27XBR50
|
Part number for diode d-251 (x1 board) 8-719-110-48 | There was no video or audio, the screen blanked. if thescreen control is turned up, the display showed no vertical sweep andhorizontal pulled in three inches from both sides. | ||
| SONY |
SSM721AMR
|
Part number is incorrect for fbt,9-997-901-01 | 9-994-075-01 is listed as part number for flyback transformeron the ssm-721am monitor. in reality, this is the part number for theflyback on the ssm620am monitor and they are not interchangeable. pleaseprovide the correct part number for the flyback on | ||
| SONY |
CCDF301
|
Spot in picture from ccd | There was a spot in the picture which was most noticeable when shooting a light or white surface. | ||
| SONY |
KV27EXR25
|
No operation, replaced ic-651 on the "g" board | Inoperative set- hear relay click. |