Sony Repair Tips
Search: sony
Results: 20077
Results: 20077
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| SONY |
CFSW430
|
Batteries burst and leaked | Customer used wrong power cord when operating from ac.battery disconnect switch was not activated by a smaller plug. as aresult, the unit power supply was providing continuous charge voltage onbatteries. -hq comments: the part number of the power cord | ||
| SONY |
SPPA60
|
No power in base - resolder d5 | No power in base. measured voltage on d5 and found it to becold soldered. this also pertains to serial numbers 35421 and 69370. | ||
| SONY |
D303
|
No mechanical motion of sled motor - tighten m-902 | The unit turns on but there is no mechanical motion becausethe wire connected to the feed motor assembly m902 is cut off. the feedmotor is not mounted securely. the screw to mount the chassis wasloosened either by shock or the vibrations of the motor r | ||
| SONY |
FD555
|
Intermittent picture, and brightness. resoldered c803 | The unit would intermittently loose picture or brightnesslevel, when touching the board it would change. the horizontal osc.signal level changed between the positive and negative side of c-803horizontal drive couplying capacitor which delivers the horiz | ||
| SONY |
CCDTR200
|
Rattle noise/normal operation when no power is applied | The customer complained of a rattling noise when the camera isshaken back and forth. | ||
| SONY |
KV27EXR20
|
"h" bracket part number missing, 4-397-916-02 | On the chassis exploded view i need the plastic bracketbehind reference number 3, which clips on to the h board. this partnumber was omitted from the service manual. -hq comments: the part number is 4-397-916-02. this part is notavailable from kcp at | ||
| SONY |
KV27EXR25
|
"h" bracket part number missing, 4-397-916-02 | On the chassis exploded view i need the plastic bracketbehind reference number 3, which clips onto the h board. this partnumber was omitted from the service manual. -hq comments: the part number is 4-397-916-02. this part is notavailable in kc at this | ||
| SONY |
KV32XBR95S
|
No channel caption in aux mode, normal | In the aux mode the customer can not use the channel captionfeature (example channel 4 as nbc). when they bring up the menu thescreen turns gray. there is no mention of this in the owners manual. -hq comments: this is normal operation, the channel cap | ||
| SONY |
KV27XBR95S
|
No channel caption in aux mode, normal | In the aux mode the customer can not use the channel captionfeature (example channel 4 as nbc). when they bring up the menu thescreen turns gray. there is no mention of this in the owners manual. -hq comments: this is normal operation, the channel cap | ||
| SONY |
CCDFX310
|
No camera picture e-e/replace ic 704 | There was no camera picture e-e and there was intermittentcharacter display. when character display rolled vertically, i foundthere was no vd out at pin 73, ic704. | ||
| SONY |
SPP100
|
Availability of gray handset cabinet | I have a spp100 which is black and i need to know if there isa part number for the cabinet in black instead of ivory. specifically,the front cabinet item number 51 on page 28 of the service manual. -hq comments: please refer to supplement (p/n 9-952-20 | ||
| SONY |
SPP190
|
No channel lock pll off - replace x-1, p/n 1-567-773-11 | The handset would not lock on channel. i tried the squelchadjustment but it would not lock. i found an output rf frequency off andtried to adjust ct1 which would adjust, but not far enough. | ||
| SONY |
SLV900HF
|
Horizontal tearing/distortion: resolder q806 - rp-149 board | The picture is distorted during playback. there is horizontaltearing and saturated color (little or no luminance). | ||
| SONY |
SLHF360
|
Loading mtr does not fit: file off small nipple on bracket | The servicer received a replacement loading motor which doesnot fit. reference number 107 bracket motor has a tab/post which fits ina hole on the original motor. the replacement motor does not have thehole, thus the motor does not mount flush with the | ||
| SONY |
MDP455
|
Unable to track outer edge of ld: optical assembly | The unit will not track properly at the outer edge of thedisc. | ||
| SONY |
MDP605
|
No b side pb or no pb: clean elev. wiper & repair cn317p | Unit will either stop on b side play or it will not play atall. | ||
| SONY |
D515
|
No tracking - resolder ic-504 | The unit would focus search and shut down. i found fokpulses, but it would not track. | ||
| SONY |
D515
|
No audio in esp mode - resolder ic-601 | The unit would play fine in normal mode, but it would muteaudio in esp mode. the display would also show no accumulation of memory. | ||
| SONY |
SLV900HF
|
Intermittent snow in video: resolder rp149 shield to board | Intermittent snow in video. | ||
| SONY |
SPPS10
|
Bad reception in handset - broken etch from q501 col to l506 | The unit's handset had bad reception on both channels whichwas decided from the analyzer. i measured the 10.24 mhz at connection #1of 455 if pcb, which was good. the 455 khz did not look good coming outof connection #4. i measured all the transistors |