Sony Repair Tips
Search: sony
Results: 20100
Results: 20100
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| SONY |
D515
|
No audio in esp mode - resolder ic-601 | The unit would play fine in normal mode, but it would muteaudio in esp mode. the display would also show no accumulation of memory. | ||
| SONY |
SLV900HF
|
Intermittent snow in video: resolder rp149 shield to board | Intermittent snow in video. | ||
| SONY |
SPPS10
|
Bad reception in handset - broken etch from q501 col to l506 | The unit's handset had bad reception on both channels whichwas decided from the analyzer. i measured the 10.24 mhz at connection #1of 455 if pcb, which was good. the 455 khz did not look good coming outof connection #4. i measured all the transistors | ||
| SONY |
SPPA40
|
Plunger not kicking - change q-26 in base, p/n 8-729-201-53. | After outputting the ogm, the unit beeped. the motor spun,but the plunger did not kick. when going to the plunger, the 6v was notthere so i went to q26 and found the base was going lower then theemitter (pnp), but the collector was not going high. i f | ||
| SONY |
SPPA40
|
No audio from base to speaker of the handset - pin 20/ ic-3 | When powered up, there was no audio in the handset but therewas audio going to the phone line. when putting the handset in test mode,there was static indicating the handset was good. tracing the audio inthe base from the phone line to ic7 - ic6 then to | ||
| SONY |
BM88
|
When tape is inserted, unit goes into listen mode, c214 | When the unit is powered on, the alarm tone sounds, and whenthe tape is inserted and placed into the transport mechanism, the unitgoes into listen mode. when the stop function is engaged, the head baseand pinch roller move back. as soon as the stop but | ||
| SONY |
BM77
|
No display, replace d107 | Segments did not display and only the back light would come onwhen powered on. (this problem sometimes has the unit completely dead dueto open ps101. | ||
| SONY |
BM88
|
No display, replace d107 | No segments displayed and the back light is on when poweredon. (this problem sometimes has the unit completely dead due to openps101. | ||
| SONY |
BM77
|
No tone control, replace c130 | The tone control does not work. | ||
| SONY |
BM77
|
Weak audio, cold solder on c109 | The audio was weak and a hiss was present through the speaker. | ||
| SONY |
BM88
|
Weak audio, cold solder on c109 | The audio was weak and a hiss was present through the speaker. | ||
| SONY |
BM88
|
Noise in the audio with vsc mode engaged, replace ic109 | When the unit was put into listen mode and vsc was engaged,a pulsating and hissing noise was heard through the speaker. when vsc wasoff, the audio was fine. | ||
| SONY |
KV27EXR20
|
Will not turn on when cold, replaced c-655 ("g" board) | The set will not turn on when it was cold. | ||
| SONY |
LANCJIG
|
Jig does not function after installing new software;autotime | After installing the new software version, the jig will notfunction. | ||
| SONY |
KV32XBR95S
|
Set shuts down immediately after turn on: replaced ic-1402 | The set will shut down immediately after turned on. | ||
| SONY |
LANCJIG
|
Evr transfer does not work for one page cameras; new softwar | One page cameras do not work for evr transfer. | ||
| SONY |
LANCJIG
|
No communication with com 3 selected; select irq 10 | I have no communication when i select com 3 in the systemparameters menu. | ||
| SONY |
M2000
|
Auto backspace does not work | Auto backspace does not engage. a shifting lever in themechanism which shifts gears reference numbers 80, 82 -performs functionsof fast forward and fast rewind. it does not shift smoothly and quicklybut the functions of fast forward and fast rewind do | ||
| SONY |
FD230
|
Unit is draining batteries even when the unit is off, cn601 | Even when the unit is turned off, the current across the powerswitch is 19 ma. i found cn-601, which is next to the power switch s-601,mounted in the reverse position from the factory. | ||
| SONY |
TCW311
|
Mech chassis is unavailable and needs replacement | The sub chassis is not supplied per service manual breakout.can you supply a part number, or whole chassis assembly part number, orgive a suggestion as to what to do? the part of the sub-chassis thatsupports the pinch roller is cracked. -hq comments: w |