Sony Repair Tips
Search: sony
Results: 20100
Results: 20100
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| SONY |
SPPA40
|
Answering machine would record icm for only ten seconds. | The unit came in recording an incoming message for only tenseconds. ic3/pin 27 (vox input) should have pulses during icm from thepb/rec amp ic15/pin 25. i noticed there were no pulses in the bad unit.following it back to ic15/pin 12 (audio input), i fo | ||
| SONY |
CFS905
|
No motion from the mechanism-reposition slider(ref 170) | The mechanism was stuck in pause. after inspecting themechanism, i found the slider (ref #170) had popped out of its retainingclips on the chassis assembly, which holds the cassette in a pause mode. | ||
| SONY |
KV19TS20
|
Snow, replace tuner | Only static would come when powered up. after hitting thetuner, the picture would come back. | ||
| SONY |
FDL380
|
Screen would only play for 15 seconds, fluorescent tube | The set would run for fifteen seconds before it would blackout. the fluorescent tube would darken on end and protection circuit would kick in. | ||
| SONY |
KV13EXR91
|
No remote operation, replace detector ic103 | I checked the voltage to ic103 and gnd and it was fine,but there was no signal out. | ||
| SONY |
KV2691R
|
Set shut down at start up, open c609 | I found a ripple on the retified standby line. | ||
| SONY |
STRD790
|
No surround - r628 faulty p/n 1-249-389-11 | No surround at all. | ||
| SONY |
KV32XBR25
|
Intermittent pix, resoldered q2303 on "e2" board | Intermittently there was no video, channel display o.k. | ||
| SONY |
KV27TS27
|
No video, replace ic-301 | There was no video, raster (dark) intermittently. the soundwas fine though. | ||
| SONY |
KV20TS27
|
No power, replace ry601 | No power. | ||
| SONY |
PVM2530
|
Retrace lines, top of picture | The picture was distorted with retrace lines on the top. | ||
| SONY |
KV13TR27
|
Snow and no display, resoldered 5v regulator ic | There was no picture instead, raster and snow appeared. inaddition, there were no channels or volume display. | ||
| SONY |
CPD1302
|
Shuts down immediately when rgb cable is connected to pc | The unit would shut down immediately after the cable was connected to the computer. | ||
| SONY |
CPD1604S
|
Intermittently loses green, cold solder on r526 on "b" board | The monitor would intermittently lose green. | ||
| SONY |
STRAV920
|
Display out but operation ok - faulty solder r202,203,242 | The unit had no display, however, operation was normal.tapping around the left front part of the unit caused the display toflash. | ||
| SONY |
SLV585HF
|
No drum rotation. eats tapes./ cn007 md49 board loose. | No drum rotation and it ate the tapes when the tape was loadedand play was hit. | ||
| SONY |
SPPA20
|
No range | There is no range from the handset. | ||
| SONY |
ITA550
|
Inoperative - replace ic-203, p/n 8-759-945-88 | Inoperative, and the ac adaptor (ac-t145) was getting hot. | ||
| SONY |
CCDV5000
|
Auto focus question | We need to know at what point the auto focus sets the lens ata fixed point when in wide angle zoom. we cannot locate this informationin the service or owners manual. are we overlooking it or does this modelhave a different mode of operation?? please l | ||
| SONY |
CFD440
|
Cd not operational - replace ic-802, p/n 8-759-971-11 | No power. i only repair cd mechs, and of the ones i do, about1 out of 20 has this problem. |