Search: sony
Results: 20100
Make Model Symptom Problem Solution By
SONY SLV575UC
Audio buzz in hifi pb- self recordings. adjust ctl head Buzzing noise on self recorded tapes only. monitoring rfenvelope i noticed a gap between a and b heads areas. the gap disappearsduring the last few seconds of each recording.
SONY CDPC325
Drawer opens and closes continuously when powered on When unit is powered on, the drawer will open and close untilunit is turned off. i found the right side of mcb had come loose fromfinger snap. this was shorting mcb to bottom of metal case. (i alsonoticed that the left side of mcb was in the correct p
SONY SPPS10
Intermittent tx in channel 9-replace c-539, p/n 1-163-183-00 When twisting the main pcb, the transmit frequency on channel9 would jump from 49.990 mhz to 50.064 mhz. going to the channel 9 txcrystal x505, i discovered that when you twist the pcb, the frequencywould change. after visibly checking the board i fou
SONY TCWR670
Tapes stuck in unit while dubbing - q701 faulty 8-729-620-05 While dubbing, both decks locked up, but display stayed lit.
SONY CCDF40
Distorted color (slight distortion) l381, va40bd Found noise in color which was a very minor wave, littlenoise.
SONY CCDFX410
Not recording video but playback is fine/ l002, cs31 No video is recorded on tape, but playback is fine. i checkedfor (rec c rf) and (rec y rf) signals and all were there. i also checkedd.c. voltages and found no voltage to video heads.
SONY KPR41EXR95
No reception on channels 2 through 6., replaced tunner Channels 2 through 6 will not function, all other stations areok. tuner pins voltages measured normal.
SONY KV27XBR35
Intermittent uhf tuning, replaced tuner Uhf channels distort after about twenty minutes of operationand then all uhf channels will be lost. vhf is not affected.
SONY CDXA20
Jammed mechanism, e-99 displayed (clean q-403 on ehs board) During operation, if switching from disc 1 to disc 10,elevator would go too high or stop in wrong position. while checking thetiming of large elevator gear, i found the top looked scraped. so ichecked q403 on ehs board and found the slot for phototrans
SONY CCDFX410
No video in playback/c6, cs-31 leaky No video in playback but camera and record worked fine. isuspected ic1, but that did not fix the same problem. after checking alld.c. voltages, the voltage on pin 31 was 2.8 vdc, and it was supposed tobe 2.1 vdc. all other voltages were correct and on
SONY ITA4000
Buzzing sound in handset - replace ic-301, p/n 8-759-979-34 There was a loud buzzing sound in the handset. the speakerphone was ok.
SONY KV32XBR95S
Pin cushion distortion, replaced q-506 Picture was bowed in on the sides.
SONY CCDTR71
No pb video/resolder l007, vs-93 No pb video.
SONY STRAV270X
Unit inoperative - b+ solder short to ground on display bd B+ regulator q701 was heating up and r703 was glowing hot.when cns501 is disconnected, the regulator runs normally, thus short is ondisplay board. after troubleshooting display board, i traced the shortto an area where ic-302 would be placed when mcb is
SONY ITA4000
Low sound in playback when message is retrieved Low sound (in playback) when message is retrieved.
SONY D202
Unit will not engage play - play switch defective Unit will not engage play.
SONY D101
Unit will not engage play - play switch defective Unit will not engage play.
SONY D808K
Unit will not engage play - play switch defective Unit will not engage play.
SONY KV29XBR85
Shutdown going into video menu, no solution at this time I have had five anu chassis units that momentarily shut downwhen an adjustment (customer) menu is entered. i have seen this beforeand a new rom ic-102 fixes it. these units replacing the rom and micodid not cure the problem. hq comments: we have recei
SONY KV27XBR55
Shutdown going into video menu, investigating I have had five anu chassis units that momentarily shut downwhen an adjustment (customer) menu is entered. i have seen this beforeand a new rom ic-102 fixes it. these units new rom's did not fix, nordid changing the micro. i am sending you the a board