Search: sony
Results: 20100
Make Model Symptom Problem Solution By
SONY KV27S22
AA-2
Picture interference Sony kv27s22. serial 8126359 the sound is increased to a 60 to 80% level the crt will exhibit an effect on the sides resembling a ""water fall"" effect. it disappears if the audio is muted or if the audio level is dropped down to a lower level. "" This symptom is called 'acoustical vibration."" it is caused by the sound energy from the speakers coupling acoustically through the crt frame to the aperture grille inside the crt. the vibration causes the aperture grille assembly in the tube to vibrate. suggested customer use external speakers "" Muller
SONY KV36FS12
AA-2
Noisey video This television had sever noise resembling black & white random lines of varying lengths. no discernable picture. noise is in the tuner and video and modes. Checking the video at the input of the comb filter ic3504(2) on the rear i/o circuit board. the video is perfect. however the luminance out ic3504(9)is broken into pseudo square waves that are random in size and shapes. this indicated the combfilter was not working. further checking discovered the fsc ic3504(37), which is a 3.58mhz carrier was reduced to a 60hx pulses. at cn271(15) we found the fsc signal normal. problem was an open trace between the connector cn274(15) and c3578 located inside the combfilter shield located at coordinates c2 on the uy board. Muller
SONY KV32V25
AA-2
No video Kv32v25 unit has no video when using the front input jacks. all other inputs are o.k. When tracing the video signal from the front input connector we find good video on the connector but less than an inch away from the connector is a coupling capacitor c2233. apparently the trace was torn after the video input jack entered the board. placing a hard jumper wire from the jack to the c2233(-) corrected the fault. Muller
SONY KV32S22
AA-2
No raster no sound Kv32 unit has a horizontal line across center of the screen. the line is elevated above center by 2 inches. tsound is no sound too. no led's in front are blinking This symptom is inductive of a problem in the data or clock bus. measuring the scl & sda i found the scl was running at 1 volt peak to peak and the sda was at 4.97 volts pp. i had the tech start pulling all of the stand up boards out of the mother board to isolate the sda & scl lines. after the main tuner was removed the scl returned to normal. replacing the main tuner corrected the trouble. Muller
SONY KV20VM20
AA-2
No raster Sony kv20vm20 unit has no raster but sound and osd are o.k. Unit did not have any horizontal blanker pulse to pin 19 of the jungle ic. shorted z1403 unit had 60 peak to peak at the ""fp"" of flyback. at cathode of z1403 should be 7 volts peak to peak. replace diode and restored normal operation. "" Muller
SONY KV32V40
AA-2
No raster Kv32v40 unit has no raster. when g2 is increased the unit has a non uniform bright screen, brighter at the top of the screen. the television has sound. Cure: checking the +12 and -12 volts at ic561(2&4) respectively are normal. monitoring q561( c) it was only 1.7 volts (wsound it should be about 3 volts), and q561(b) was 0.6 volts( wsound it should be ""0"" volts).. the voltage at q562(b) is always low (0.11volts). by pulling the base q562(b) high, with a dmm in the diode check mode, we are able to get full vertical sweep. it appears tsound is no, or poor pulse coupling between the fb pulse u561(3) and q562(b). a strong pulse is present at u561(3) when grounding q561(b). no pulse at c564(+) tech needs to replace c564 1mfd @ 50 volts was "" Muller
SONY KV32S65
AA-2
No raster Kv32s65 serial 8014809. unit has no raster. sound o.k.. led on front panel flashing. it also does have high voltage. I had tech measure the g2 voltage at the crt. it was only 54 volts. with the socket disconnected the g2 voltage returns to 410 volts. unit has defective crt. crt must be replaced a80jyv52x Muller
SONY KV32S25
AA-2
No raster Kv32s25 has no raster. when the g2 is increased the set has a partial raster but brighter at the top of the screen then the bottom. measuring across the vertical yoke windings we find tsound is a voltage of approximately 8 volts. these is sound and channels can be selected. The symptom indicates the set has a vertical deflection failure but more precisely a power supply failure for the _15 volts power supply. the tech either has a open r536 = .47Ω @ or open d530. . Muller
SONY KV27S20
AA-2
No raster Kv27s20. unit has no raster. tech had replaced crt but the symptom was not corrected power light still flashing indicating the unit is in the stand by mode Open trace on the crt driver board causing the ik pulses not to be returned to cn1761(6) not to be fed back into the jungle chip. Muller
SONY KV26V36
AA-2
No raster Kv26v36 unit has no raster. further checking we found the set had high voltage and vertical sweep. just no filaments. I had tech check the must haves. the only thing that was not present was heater voltage. i had the tech remove the socket and measure the total resistance of the filament power supply by measuring the h1 & h2 terminal pins on the ""c"" board. it was open. h1 & h2 at the flyback were less than 1Ω. checking cn503 found the black wire was loose and fell out of the connector when unplugged from the main board. connector wire would stay in place if reseated. pushing connector back in place corrected the trouble. "" Muller
SONY KV32V25
AA-2
No highvoltage Kv32v25 serial # 7014651. unit has no high voltage. The horizontal driver has tremendous amount of ringing on it. does not replace if we remove horizontal output transistor. the transistor has drive has 7 distinct pulses on the base that go above and below the cut off point of the transistor. these seven pulses are 1 microsecond in duration and are grouped in clusters after wsound the horizontal drive pulses are supposed to be. if allowed to operate for more than a minute the horizontal driver transistor q502 will short c to e. the product has a bad jungle ic301 Muller
SONY KV32S25
AA-2
No highvoltage Kv32s25 unit will not develop high voltage. when the set is turned on no high voltage appears. the set has sound and has a flashing light on the front indicating the set is still in a stand by mode waiting for ik pulse feed back acknowledgement from the jungle ic When monitoring the horizontal output collector we found the 140 dropped slightly at turn on. but the horizontal driver q501(c) dropped to 85 and back up to 140. i had the tech to remove the horizontal output transistor and try starting up the set again. after power up measure the q501(c) horizontal driver transistor. it should be about 85 volts and stayed. this told us we were looking at a shutdown symptom. checking all secondaries we found nothing shorted. replaced flyback which corrected trouble. Muller
SONY KV27S25
AA-2
No high voltage Kv27s25 serial 811908. unit has no high voltage. led in front is flashing on and off after power up. tsound does not seem to be any horizontal drive to the horizontal drive transistor. defeating the horizontal output by removing the collector connection still will not allow horizontal drive to appear at ic351(37). this pin is sitting at nearly 8.5 volts, not the 3 volts it is supposed to be. also ic351(38) the hoff/afcpin is at 3.3 volts which is normal Looks like the tech has a bad ic351 cxa2025as. a second jungle ic corrected the problem. Muller
SONY KV32XBR48
AA-2
No chroma pip Sony kv32xbr48. no chroma in pip X3304 0n px board not soldered (pip) Muller
SONY KV27S15
AA-2
No chroma Kv27s15 unit has no chroma. black & white is ok. also no chorma while using the pip. sound and on screen display ok. initializing eprom does not change the effect. Scoping the first place wsound the chroma signal can be readily available is on the pip module. they are marked ""c in"" & ""c out"" on connector cn501(1 & 5). we have chroma going into the pip board but nothing coming out. jumping these pins together with a 1 mfd capacitor caused the color to return, as long as the capacitor was in place. unit has bad "" Muller
SONY KV36FV75
AA-2
No audio Kv36fv75. unit has no audio. but also has no osd stating ""main"" or ""stereo"" main picture is fine. "" Id codes are 0=25, 1=55, 2=47 3= 0 , 4= 155, 5 =143, 6 =6, 7=0 which is correct. initializing the eepom did not correct the trouble. tech will be returning with a manual Muller
SONY KV27V22
AA-2
Intermittent snow Kv27v25 unit has intermittent snow in the picture zthe tuner pn# 8-598-340-20 was replaced. now the set has a symptom wsound the remote control causes the set to enter the video input mode when the channel is selected. also the set will enter the video input mode if the and another brand of remote that operates a stereo receiver will put the set into the video input mode. I instructed the tech to enter the tech mode and set the id codes...id0=25, id1=23, id2=47, id3=0, id4=27,id5=135, id6=1, id7=0 . write these in memory, then press ""8"" ""enter"" to initialize. this corrected the problem. "" Muller
SONY KV32S26
AA-2
Int raster Kv32s26 unit has a brighter than normal picture. when g2 is lowered the picture blinks on an off. tech replaced the flyback and jungle chip with no changes in symptom I had tech short the cn1761(1, 2, 3, & 6) together. this should give a perfect black and white picture. but when this was shorted we had a black and white picture but the picture still was flashing. since the jungle ic was already replaced it was assumed the ik pulses were ok from the jungle chip. the main concern is if the pulses are leaving the main board, and if the pulses are getting back to pin 27. this flashing condition indicates the ik feedback pulses are insμFficient some wsound in this path. further static check indicated a shorted zener diode d1792 in the ik bμFfer path on the crt Muller
SONY KV35V75
AA-2
Horizontal sweep Unit has shorted l511 and q512. tech replaced these items and they burn out again Tech needs to replace d503,d502, d504 and c511, c512 the retrace capacitor along wit the other components. Muller
SONY KV36FV1
AA-2
Horizontal sweep Kv36fv1 serial 9023663 unit has a sever over scan condition for horizontal sweep. tech did not measure any voltages in the pin amp circuit Tech needs to check on l511, q512, c513, c511, d502 & d504. one or more of these are shorted. Muller